Hi guys,

I have started making the model from 12inch foam plates, here is the progress so far. Targeting AUW to be under 3 grams with out electronics (one wing missing in Picture/weight add 0.56 grams).
one can download the plan from below link, (Print Blu-Baby 24 Parts Kit Full-2 to 47% scale).
http://www.rcgroups.com/forums/showthread.php?t=681556

fuse

Wat about electronics you had selected and from where you got 12 inch plate
If you don't mind.

Thanks

Thanks Sahil for the link Can you please point to the exact reply number where the micro plan is available in RCG thread.

Edit Now Noticed this Thanks

(Print Blu-Baby 24 Parts Kit Full-2 to 47% scale).

QuoteWat about electronics you had selected

i will be using supermicro 3ch 2.4Ghz Rx(<1gram with wires), turnigy 130mah 3.7v (4grams), 7mm quadrotor motor/prop (3.5grams). and home made actuators (<1gram).

Quotefrom where you got 12 inch plate
If you don't mind.

Plates are called thermocol plate or foam plates or biopack plates etc they some in 25/100 pack, 25 Nos 12inch pack costs Rs 45/-.

https://www.google.co.in/search?q=biopak+plates&client=firefox-a&hs=HU2&rls=org.mozilla:en-US:official&channel=rcs&biw=1280&bih=676&source=lnms&tbm=isch&sa=X&ei=1KE6VKCZKM-zuASBhoKACw&ved=0CAYQ_AUoAQ

Try justdial in your city(will post pictures later).

update

One more question which one is full 2 and what do you mean by 47%
Hope you are not getting annoyed

okay Print the attached PDF in fit to page (A4) which is 47% of the original size (hope i'm not complicating this)

sahil

Thanks for the PDF sahil 

QuoteThanks for the PDF sahil  Grin

are you planning to make one or already started ?

Planning to make. I have a packet of 12" plate.

great 

Very much thanks for clearing my doubt

finished the coil actuators (96ohms each). Its getting closer to flight and heavier 

finished and crashed the model , AUW was 13.5 grams. It flew well with limited control (rubber only), had i used elevator it would have been a different story

will post the video link.

Nice build sahil 13grams great ,im still stuck on drives

here is a iphone video

QuoteNice build sahil 13grams great ,im still stuck on drives

Thanks roman, although model is in no-flying condition, planning to make v1.1 with 16 or 20 inch WS and under 14grams 3ch.

Nice mini micro plane, Sahil.........The model flew quite good.....only all of a sudden it went into a spin, what was the reason?? did you find out? the blue baby has enough lift due to the under chambered wing. What were the wind conditions when you flew your model,Is it not possible to fly it indoors, say in the living room??

Quoteonly all of a sudden it went into a spin, what was the reason?? did you find out?

Plenty of reasons, too big a motor, lack of elevator, rubber only control, poor dihedral. Actually it was a loop which made the model uncontrollable.

QuoteWhat were the wind conditions when you flew your model,Is it not possible to fly it indoors, say in the living room??

there was a bit of cross wind and due to high AUW/DD motor setup i doubt its possible to fly in a room.

The best part i felt about all this is i still got my model trimming skills 

what ever it flew  , climbed well thou ...was this your first micro sahil

yes it was my first micro.

I thought before i take another dig at Blu-baby i might build a actual micro model from plans so here is quick junior  and struck at remote actuators 




 

For interested builders plan can found in below link.

http://www.rcgroups.com/forums/showthread.php?t=181173

or

http://www.rcgroups.com/forums/showatt.php?attachmentid=905462

sahil excellent your first micro ,good choisce the blu baby  that too outdoor flying grest.....all the best with the junior he is coming out good whats the wing span ... i think your blu baby can fit in here http://www.rcindia.org/electric-planes/successfully-flown-micro-airplane-thread-only/msg154372/#msg154372