micro slow flyer the balsa Tortoise

Started by romanxdsouza, November 29, 2014, 04:21:29 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

romanxdsouza

 the balsa Tortoise is inspired by the F1R models except mine is a bit heavier  :banghead: building is different compared to my balsa snail which is r.i p now and guts used here
here are the specs
wing span -24 inch x cord 7 inch ,detachable
stab - 11inch x4inch , detachable
fuse 21- inch made in the form of a hollow balsa tube ,detachable
rudder - 4inch
covering -  plastic laminate above brown book covers
electronic - mini vapor guts
auw -14grams - 16grams
batt- 60-70mah
balsa- 1mm sheet

romanxdsouza

#1
Some more pics

romanxdsouza

#2
Here are some more pics

romanxdsouza

#3
More pics on the fuse .

manojswizera

Superb, Romax  {:)}   Another cute micro...
Russ-40 Trainer, Mr.moss, Pushler, Skysurfer, Mugi , F-22, Red swan, Xtra-300, redfury, flying mantaray.

kiran rc


K K Iyer

@romanxdsouza
Excellent! (As usual)
I can see the thread marks, but am curious to know know how you made the tube, especially the taper, and what thickness did you use.
Regards.

romanxdsouza

#7
Quote from: K K Iyer on November 29, 2014, 08:25:58 PM
@romanxdsouza
Excellent! (As usual)
I can see the thread marks, but am curious to know know how you made the tube, especially the taper, and what thickness did you use.
Regards.
Thank you much sir ,the thread marks dont actually consern the fuse sir it was my idea to tighten the joints. regards the fuse i followed the same steps in the videos below but added a bit of my own grey matter.for the fuselage i used 1mm balsa sheet sanded it to 0.34mm or so i cut 2pieces  of 1mm balsa sheet 12inch x 1inch for motor stick and 9inch x 2cm or so not sure for boom,the 2cm and 1inch cut side will vary depending on how think you want the fuse tube ,these cut pieces i then soaked in normal water then wraped it around a wooded dowel ,put pieces of paper and cello tape to join the center then let it dry for 30mins....for easy explanation to the fuselage i added links to videos below..

These videos are of the rubber powered i used the same concept
(fuse)www.youtube.com/watch?v=UyCL-8Cdh4Y
(wing)www.youtube.com/watch?v=frrI2cKFBCk
(prop)www.youtube.com/watch?v=ZnzZJWhpYys

shijin ps

Another awesome build to your hanger. (:|~ {:)} :thumbsup: :hatsoff: Expert micro builder.
Spektrum dx9,Turnigy 9x,walkera,HK t6, Skysurfer v3,yak 54 3d,custom made Tricopter,HK Parafoil,Hausler 450 heli,hiller hover 450 heli,Ornithopter,

romanxdsouza

#9
Thanks shijin ,
And finally what you all have been waiting for  :thumbsup: :thumbsup:
www.youtube.com/watch?v=_TqbqIU0CEU
www.youtube.com/watch?v=KYNrGpFsrGs
www.youtube.com/watch?v=29rBZhkSkmA

romanxdsouza

If interested in micro airplanes please have a look here ,please read post #1, before you post your builds
http://www.rcindia.org/electric-planes/successfully-flown-micro-airplane-thread-only/msg204548/#msg204548
and
If interested in slow flying airplanes please have a look here ,please read post #1,before you post your builds
http://www.rcindia.org/electric-planes/show-off-your-scratch-built-slow-pace-slow-flying-airplane-only-(with-rules)here/msg152509/#msg152509

K K Iyer

Roman,
Change your RC skills category to ADVANCED at once.
No beginner can build/fly like this!
Fantastic!

shijin ps

Spektrum dx9,Turnigy 9x,walkera,HK t6, Skysurfer v3,yak 54 3d,custom made Tricopter,HK Parafoil,Hausler 450 heli,hiller hover 450 heli,Ornithopter,

sundaram


sahilkit

Today might be a great and wonderful day. It depends on you.

romanxdsouza

Thank you all,need a good place to fly now

romanxdsouza

#16
Heres a close up video
www.youtube.com/watch?v=uKpQfI72Sks

intorc

Hi Roman, excellent work! Can you do a closeup of the control surface movements? Not sure but are you controlling elevation with throttle only?

KALYANPRODHAN

Nice build...  Congrats....
Iyer Sir, the most knowledgable persons of this forum know how depth the sea is day by day, and his position... that is why members of this forum are reducing their status from Advance to intermediate and afterwords begineer... ;)

Lets viewer have the capacity to increase his reputation power... think over it sir... ;)
We have to unite and to prove ourself to make indigenous products as well as marketing / Canvasing them. I'm sure we must achieve success if we try unitedly.

K K Iyer


romanxdsouza

#20
Quote from: intorc on December 03, 2014, 08:29:22 AM
Hi Roman, excellent work! Can you do a closeup of the control surface movements? Not sure but are you controlling elevation with throttle only?
thank u all once again, yes intorc elevation is controlled with throttle however the elevator is raised a bit at the traling edge to give it lift ,see in the picture below,here is a video of the gear used
www.youtube.com/watch?v=xLDu0XRc0Ts

romanxdsouza

And here is a video of  how the parts detach
www.youtube.com/watch?v=uTv-8yiTkKM

VC

Our own Roman is giving the Japs a run for their money! Lovely craft and beautiful build.
Growing old is mandatory, growing up is optional!

sahilkit

roman why not post a build video of various parts.
Today might be a great and wonderful day. It depends on you.

romanxdsouza

Quote from: romanxdsouza on November 29, 2014, 11:03:04 PM

These videos are of the rubber powered i used the same concept
(fuse)www.youtube.com/watch?v=UyCL-8Cdh4Y
(wing)www.youtube.com/watch?v=frrI2cKFBCk
(prop)www.youtube.com/watch?v=ZnzZJWhpYys
The parts are basicly build using the same concept as from the videos  above.nothing complicated at all ,just needs practice.only thing difficult to find  here is, i think the rubberband  :headscratch:  and place to fly  :giggle:. And offcourse electronics if you are goin to be using.