Fried my FS-I6s radio by Reverse Polarity. (Help me Out)

Started by YashasR, September 06, 2017, 04:39:07 PM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

YashasR

 :help: :help: :help: Today when I was inserting the batteries in my remote, I noticed a orange glow and burning smell from the connector area. I instantly took out the battery and this happened for about 2 seconds. Then I agained tried with the correct polarity and it didnt switch on. :banghead: I have attached some pictures of the Transmitter and the circuits. Visually, I can only see the fried capacitor. I read many more forums on this issue based on similar transmitters from this manafacturer. In most of the cases there is problem in the voltage regulator and the capacitor.

Flysky / Turnigy 9X Reverse Polarity Repair Forums.
RCGroups : https://www.rcgroups.com/forums/showthread.php?1415356-Repair-Your-Fried-Turnigy-Flysky-Eurgle-9x-Radio-%28aka-Reverse-Polarity-and-You%29
Youtube :
OpenRCForum : http://openrcforums.com/forum/viewtopic.php?f=44&t=338
Instructables : https://www.instructables.com/id/How-to-repare-a-fried-Turnigy-9x/
Flite Test : http://forum.flitetest.com/showthread.php?786-Turnigy-9X-fried-reverse-polarity

Please do check them if anyone wants to for reference and help me out, I have no idea what has been damaged apart from the capacitor. :'(
Some Component Details Used in this :
Voltage Regulator : 6206A (Not sure but I think it is a 3.3v regulator as I saw at some places on the net)
Capacitor (which I guessed by a similar sized capacitor located near it but I am not sure) : 476A (10v 47uf)

sanjayrai55


sanjayrai55

Request Banggood to name it as PCB board and it should come through without Customs Duty in ordinary registered post

prabal276

sanjay sir,
Will the motherboard for Th-9x work in FS-i6s?

sanjayrai55

I'm not too sure. Maybe you could check with girishsarwal

sanjayrai55

To tell you the truth, I didn't realise the link was for TH9. My apologies

Balakrishna Reddy

It looks like you have a burned capacitor on it according to the PCB picture from the link below.
http://fishpepper.de/wp-content/uploads/2016/09/fsi6s_pcb_layout.jpg

If you can see there is an identical capacitor nearby. Now you can buy the similar capacitor in local market and should replace the damaged one. You can even buy the regulators so that in case if they are blown out too you can replace them as well. But as per your pictures they look fine.

YashasR

Sanjay, I am having a FS-I6s radio. I just gave the link for Flysky 9X just for reference or idea. Thanks for you reply :)

YashasR

Quote from: Balakrishna Reddy on September 06, 2017, 08:43:52 PM
It looks like you have a burned capacitor on it according to the PCB picture from the link below.
http://fishpepper.de/wp-content/uploads/2016/09/fsi6s_pcb_layout.jpg

If you can see there is an identical capacitor nearby. Now you can buy the similar capacitor in local market and should replace the damaged one. You can even buy the regulators so that in case if they are blown out too you can replace them as well. But as per your pictures they look fine.
Thanks for that image but I am not able to read the figures on the capacitor in the which is burnt in mine because its not so clear. Could you post a zoomed pic of that so that I can read it, or could you give the link to the site of this image? That picture can be really helpful to me.
Thanks

Regards
Yashas

kiran rc


YashasR


YashasR

I will order the parts as soon as possible and will post a update if it works or not. If anyone has something more to share, please do. All the participation of the members was really appreciated. :)

kn8alpha

Just desolder the capacitor and clean any traces of burning. Probe across the capacitor terminal at the pads to check if any short exists.. then power on and see if it works. If it doesn't, adding a new capacitor might not help in that case.

Sent from my ONEPLUS A3003 using Tapatalk

YashasR

I am selling this TX with the USB Cable, CD Manual, Throttle Center Kit, and a Manual.
Price without FS-IA6 receiver : 2400/-
Price with receiver : 2900/-
You can use this to make your own transmitter and it's receiver using NRF24L01 and Arduino which can support more than 32ch and will work on ppm.
Go to this post by me for more details.
http://www.rcindia.org/for-sale/not-working-flysky-fs-i6s-10ch-touch-screen-radio-system/
If you have any queries, let me know on my DM