1) Can a low cost chinese r/c car converted into an r/c plane?
2) Well,i have a car from which i have extracted its rx type of system with inbuilt esc
also a simple 2ch tx
from the rx system there are many wires:-two for each-ch 1[throttle],ch.2[steer in the car-rudder in plane],led[very thin wires] and power input
Well i plan to put a brushed motor for a plane in ch 1 and 1 servo in ch 2
Will this wrk?
Please ans the ABOVE TWO questions and please give ur ideas also
Thanks in advance,
Ankur
Can you post some pictures ?
One possibility (hard to say without more information) is to take all electronics out of the car, including motor, and try to build a plane that controls the ascent/descent using motor power, and use the second channel for steering using rudder. A scratch built light weight foamie might do it, but you are still faced with issues like finding/fitting a prop on the motor, can the servo used for turning the car be used in the rudder etc.
The biggest challenge is coming up with an airfoil that can pretty much float (since you have no elevator).
All told, it might just be easier to buy one of the Rs500 planes posted earlier here !
http://www.rcindia.org/electric-planes/awing-falcon-2-ch-ir-rc-product-review-price-460rs-hyderabad/
i have 4 pic-2 of rx and 2 of tx-but they are very large in size
how to post them?
www.webresizer.com
ok i resized using my inbuit resizer powertoy from autopatcher
anyways,here are the pics
well for the 1st 1,the [y and w]wires anr ch 1,the central[r and b]are ch.2,the right[r and w]are power and the yellow one on bottom right is the antenna
same for 2nd
3rd and 4th are tx with antenna collapsed and open
another question
can we make a tx and/or rx by our selves
You need to start searching the forum ;) There is at least one attempt for create a scratch built transmitter posted here. Use the Search option from the main menu on top.
well what about the car/plane part???
I don't see how you can use standard RC components with this. For example, standard servos need 3 wires, and your reciever only has 2 per channel ? That is why I suggested, try using the entire electronics of the car.
Ankur
Great to see such enthu... reminds me of days not so long ago, when I used to have dreams of making my own TX and RX system.
Well, as to your problem...
1. The range of the system that you are using will not be much... may be used on an indoor flier
2. This is what is known as bang-bang control. The controls move either to one end or to the other. If the response of the 'servo' is slow you may be able to get it anywhere in between, provided the load does not push it back. This is acceptable in the case of the steering because you need self correction tendencies of the wheel. But to hold it steady in any in-between position will be pure luck. i.e. The actuations are not proportional to the position of the joystick and therefore does not mimic the movee dment of the joystick.
3. The transmitter has 2 switches for each joy stick. One for each extreme end of control
4. You have said that there is only two wires for each actuator. In the case of the servo, there are three wires... two to give it the supply rail and the third (white or yellow), the 'PPM' signal for control of position proportionally. When you reverse position in your Chinese system, the polarity of the wires reverses. It would be much better to discard the idea of using the servo. Instead use the actuating system in the car itself for adjustment of the rudder.
5. Weight... The systems if transported from the car could turn out to be very heavy.
6. The motor that is to provide the thrust will have to be looked up in detail. We wouldnt need reversal here which is not the case for the car. That means of the two switches in the transmitter for forward/reverse movement, you will have to disconnect the reverse switch. It also means that either motor is on at full speed or will not be powered.
7. The prop. which fits the shaft can be decided only after you have worked out other details.
Next question that you asked... Can we make a Tx and Rx by ourselves... By all means if you are a little savy on electronics ... but ofcourse it will not be as cheap as buying one. There are difficulties like frequency restrictions etc. which have to be considered... Also availability of specific components... building your own pcbs, weight of the system... Its a big project by itself ... if you know what I mean.
Hope I have been a little helpful... But keep up the enthu...
Saju
Interesting thought about using the RC car for plane... however, a boat may be a good option. considering the movements are basically in 2 dimensions.
reply to saju-
1)no prob about range- i will fly indoors and improve the range by adding a longer antenna and increasing the power of the batteries-it wrks and already chked
2)let it be-i will control it
3)same as 2
4)now thats a prob
but i thn i will tell something soon if any thoughts come
5)the rx extracted is even lighter than a esc of a plane
6)actually i thnk when flying i willl give bursts of signals if i need low speed or continuous thrust for good speed
7)well i plan to put a brushed motor system from sai and it will be sufficient
just leave abt the tx rx part i don't thnk its better than a Chinese or the futaba one just introduced by sai uncle[of ~ rs2800]
well is there any pre planned way of building tx/rx[i am tlking of a downloadble plan]
any way to convert A SIMPLE MOTOR TO A SERVO
any constructive or destructive one and may involve anything availble commonly
well in the car there was at the back ch.1 with a gearbox to accel and in the front a complex system in which the grooved motor was place on a grooved connector connecting to the wheel and used to steer the car with the motion;it is a sort of one side pulling and other side pushing system
this is similar to servo
well how can we make a boat out of it????
also i wanted to know about sirboat-how to make it???
Ankur
Yes a boat is a very good alternative. It requires a forward or reverse operation and a left or right steering. It can also be small and has no great hang-ups with weight. Here, one has to be careful about the leak of water into the boat thru the hole for the propeller shaft, alternatively you have to have an outboard motor arrangement. The only other problem is of course the path the bost will take .... it will be wiggling either left or right all over the tank.... But definitely doable.
Keep up the enthu.... and the good work
Hey Guys,Here is a boat that I made with the basic low cost RC toy. The same one that ankur is mentioning.Following are the components that I used from the RC truck that I owned.
1) I removed the RX board from the Truck by detaching the wires from the motor end in the toy.
2) I removed the motor from another Toy, and removed the gear attached at the end of the motor shaft, thereby just keeping the bare shaft.
3) Used the same Toy 6V Alkaline battery to power the boat.
4) Transmitter no change.
5) Used a high density thermacole to make the boat. This was the packaging used for the new Electric chimney installed in kitchen.This boat is completely scratch built and with just some photographs as reference.used sandpaper to shape the boat.
6) Bought a new shaft with stuffing tube and prop from India Hobby- Mumbai. Got it for Rs.200/-
Connected the motor to the shaft with a cut piece of a pen refill. Used this as a joint between the motor shaft and the prop shaft.
Connected the forward backward function of the toy to this motor.
For the rudder I have tried various mechanisms.. But found the one used here very simple and effective. I cut a piece from a expired credit card and glued at right angle on another 6V motor. Connected this motor to the turning function of the Receiver.This motor was mounted at the tail of the boat such that the end of the strip is below the boat hull and behave like a rudder when turned.Used some ear buds to limit the throw of the rudder on either side. Posting photos shortly.
Tested the Boat and moved well.. The rudder needs a little adjustment so as to centre the boat while moving. While I think the alkaline battery is definitly overweight for this boat. Will be changing it to ni-mh pack .
Was fun to make it... Will shortly post video of this.
Shreekant
Pictures
nice boat shreekant
sahil
well thats a good boat-nice work
well i asked some other ques on he previous page-please go through them also
I Agree with Saju...2 Ch is too little to control a plane. Especially with these Rc toy controls. These are merely 0 or 1 controls. Whereas plane requires more adjustable throws to the controls. This is not possible with the RC toy controls. I think the next step to using these controls is a boat. And you can do a lots with these. you can also make an Airboat with these controls. It is great fun.All you need is some thermacole and a good prop.Let me know if you need help with this.
Shreekant
u need analog control,
these tx rx are digital
i told u abt it if u remember, so u cannot use these
u may find analog controls in a much expensive car but it will exceed the cost of new rx. so no use
well how can we create an airboat
Ankur
So now you need to rename this thread to "Converting a low cost Chinese r/c car into an r/c boat"..
You are getting there....
Happy boating
well how can i change it?
anywys what about airboat?how caan we make it?
You can call me on 9833607902. Will help you with this
Shreekant
hi ankur,
actually what u r thinking is not possible at all bcoz the chinese car works on radio which is having IC called TX-2 and in Rx the IC RX-2 ,these ic's are specifically designed for operating with radio controlled short range cars and these IC's are not capable of controlling servo bcoz servo works on input signal which is PWM(pulse width modulation),and these ic's drive H-bridge which are used to control DC motor supply polarity depending upon the input ,where H-bridge will have a 2 inputs accordingly it will change the direction of rotation of motor clockwise or anticlockwise ! and these ic have 5 controls like Forward ,backward,right ,left and turbo , another thing is u can configure to work on twin engine aircraft where it will have no servo but controlled by thrust vectoring with twin engine like add power to engine climbs and reduce power it descends and vary speed btween engine it will turn accordingly.
if have doubt pls go to www.datasheet4u.com type TX-2 u will get its datasheet! if any further doubts pls let me know. 8)
well ok i now don't just want to play with the tx/rx bet will simply make a another car out of it
Looking at u r age and the question u r raising are well advance than other kids in u r class.
Good Keep it up [reminds me of u r age].
Secondly if u have desires to experiment on electronics then Go ahead,
take some adult suprevision while experimenting around u.
But if u intend to fly, then seriously dont get into electronics component level at this moment.
knowing basics electonics is more than enough for flying.
concentrate on aerodynamics rather than electroncis, aerodynamics will be more usefull for u r experiment.
Google for micro Vapor plane, this may add some reference where to begin with.
I think its best to buy those 2700 worth 2.4 Ghz Radio offered by Mr Sai (rcforallin). Nothing can beat that... you don't even get a 2.4 Ghz receiver at that price. This is all if you want to stay in the hobby and just not like paying a short visit as one used to do in vacation to their Granna's house!
One thing more, you would also need the radio to be 'Proportional' -Even the 2400 Cheapo RC plane I bough didn't had a proportional system for twin motors and if you pull the stick left/right, on of the motors used to just STOP!!
Start well so that you don't face frustration in the beginning itself.. keep energy for fruitful challenges
-Uj
http://www.rc-cam.com/microszr.htm
i added this in another thread.anyways i think this link would be of help to the topic creator.!