This would make a great beginners plane

Started by anwar, April 29, 2010, 11:25:07 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

anwar

Looks like this would make a great beginners foam model.  Pusher-prop and high wing; desirable characteristics for beginner models.  Wonder what would happen if some dihedral was also added ?

Hangar : Please see my introduction.
RC India forum and me : About this forum.

Ashta

very nice. that adds one more to my list of to make.

ashta
You can't be first because you do not know!

anwar

Hangar : Please see my introduction.
RC India forum and me : About this forum.

anwar

If anyone must get the original plan (as opposed to try and build from photos), you have to order the book.

http://www.modelflyermagazine.com/Frames/Plans/Plans11.htm#
Hangar : Please see my introduction.
RC India forum and me : About this forum.

Ashta

Quote from: anwar on April 29, 2010, 08:25:10 PM
http://www.rcgroups.com/forums/showthread.php?t=815248

thanks anwar. i have already found this yday and copied the specs and the photos to my to do plans list.
thanks
ashta
You can't be first because you do not know!

Ashta

Always wanted to try this model, from the time Anwarji posted this video.
Heres my attempt.

I first enlarged the plan at a jumbo xerox by X 3.5 times. That gave me the aprox actual size of the plan.
pl see the photos and a video

ashta
You can't be first because you do not know!

Ashta

Here is a small video. Still some fine tuning and  CG changes required
You can't be first because you do not know!

rajaram

#7
 {:)} {:)} {:)} {:)}

Nice effort Ashta
RAJARAM SHENOY G

Ashta

You can't be first because you do not know!

anwar

Hangar : Please see my introduction.
RC India forum and me : About this forum.

Ashta

You can't be first because you do not know!

RcBazaar


Ashta

You can't be first because you do not know!

VC

Maestro! You make everything look so easy with your humility. :bow:
Growing old is mandatory, growing up is optional!

rajsigma


Ashta

thanks VC. wish you and family a great new year.




Quote from: VC on December 22, 2011, 06:36:21 PM
Maestro! You make everything look so easy with your humility. :bow:
You can't be first because you do not know!

Ashta

You can't be first because you do not know!

rajsigma

sir
share build plan and electronics you used.

Ashta

just go thru this thread to get the build details.
electronics
any 1300 KV, 20 Grams motor]
any esc 6a 3cell
5 gram servo
5 gram rcvr
You can't be first because you do not know!

rcpilotacro

#19
Superb Ashta :thumbsup:
Gusty's Hangar and Introduction.

A Good pilot will practice until he gets it right,
A Great pilot will practice until he can't get it wrong.

rajeshbhanushali123

Be an engineer not just a degree holder

https://www.flyingmachines.in

Ashta

You can't be first because you do not know!

Ashta

thanks augustine
this is designed for an indoor.yes u are right will need support for wings
but every additinal wt will change its flyingcharacterestics.
thanks


Quote from: augustinev on December 23, 2011, 02:15:55 PM
Superb Ashta.

A few points for you (may be i am wrong)

(a) Wing Flex.. looks like she can make do with one more CF
(b) Tail heavy...you covered that
(c) Is it too much of Expo on the aileron, that she is jerky at slightly more throws ? could you reduce throw and expo on the aileron in the elevon config.
(d) She sure is underpowered, at the fag end of the batt you might end up short of power for recovery. touch more power, she might aeros too.

Once again :thumbsup:
You can't be first because you do not know!