33 inch blu baby build
Now control rods (or push rods) & V-stab rudder and landing gear are in progress.
Fuselage is made of 25 inch thermocol & v - stab and  h-stab are made of 5 mm thermocol.
Electronics :
A2212 1000kv with 1045 propeller
30a simon k esc(from quadcopter)  
2200mah 3s 30c lipo ( i think plane will be heavy).
Turnigy 9x transmitter & Turingy 8ch receiver

Other things Required:
need to make control rods(or push rods) but steel rods from cycle tire.
I am going to make control rods from bamboo and wire which used for Saria(TMT)
If you can tell any diy control rods build then tell me.
Wings needs to be joined together with dihedral.
I need to wait for more than 3-4 days for dry ground because of rainy season in my area.

Thanks to all people for talking with me on call & suggesting me on forum.
Special thanks to Girish Sarwal Sir.

Images here:

Looks good taksh, let's see this up in air soon

Well done.
What did you use for covering?
Try 2" wide coloured tape

For desi pushrod, see this:
http://www.rcindia.org/tools-materials-and-building-techniques/push-rods-alternative/msg179687/#msg179687
Regards

@K K Iyer sir
I have used butter paper for wings and tape (as shown in image) for covering v stab, h stab, and fuselage.
Now i am worried about maximum throw of rudder and elevator because blu baby is slower.

 your build is awesome and for your query you can use umbrella rods or whatever it is called
Its a little wife than the holes so heat it push it in and give it a slight wiggle...
It's hard to cut them though but they act just like used by flite test ...

Hope I helped...

My parents will not allow me to destroy umbrella because of rainy season.
I have 3  rods 3~5mm steel rods. I got 2 rods(very hard)  from nearest engineering works shop & 1 is from bicycle repairing shop.
Now i am thinking which is best.

Well if there are street markets, chor bazar or Hatia types market during this season there are umbrella fixers ask them they will only give if you tell it's school or college project...

Tomorrow, i will try to find umbrella fixer but if i said "i need for college or school project" then all will try to sell at high rate.
I know nearest kabadi wala. Kabadi wala selling his not working 2 x cd dvd rom driver (from computer) at 250+.
kabadi wala in poor area can sell at 30rs+ each.

My new idea is.
I will cut stick of lollipop into a size then i will insert servo control horn in lollipop stick after making big hole in lollipop stick.

Cycle rickshaw spokes are a good alternative for push rods. One side is threaded and one can easily screw in a clevis

@ taksh
Some stationery shops have a wire for bouquet making. It comes in two varieties, a thinner flexy- bendy one and a stiff one.
If you can find the stiff one, it will be excellent for the job!

@taksh
Prabal is right, the stiff one is made up of still, which does not bent easily, but you have to make it straight using flat headed hammer, it is lightest and strongest one

@prabal @tictoc21
Share images of wire with me.
I can understand things better with images.

@ taksh
My stationery has stopped stocking those wires. So cant share any photos.
They are a little thinner than cycle spokes but of the same level of rigidity.......
Just inquire once. I am sure you will find them.

I usually get the Umbrella wire from local junk yards. The actually give it for free. You can try there.

@prabal
I asked for bouquet making material and wire at 3 shops and all said "hamera pass nhi hai" or "hmm nhi rakhte".

This is the required wire

Using it on my craft right now, and it's very cheap and stiff and lightweight at the same time

Hope you can understand from pics

Ask for steal metal wire

In hardware store

@tictoc21
this wire is for TMT ( saria ). I have this wire but this wire is very flexible.
I heated up this wire with spring so wire can get hardness but nothing happened.

If you want a really great wire for the job, go to a electrical store and ask for the wire that electricians use to pull wiring through conduits. It is a hardened alloy with perfect thickness for the job and will not bulge or break or twist

You did not quench it I suppose you only heated it...

Yes it's flexible in ring format, but when you make it straight by hammering its gets hardened.

I have umbrella rods as well as thread manjha.
which end of umbrella is  for servo control horn.