Did u calibrate that ESC?

if not....then call RCB and get help from them to calibrate the ESC

no, i did not, but what does that mean ?
i will call them right away.

also check if the RX n TX are binded correctly..

with little knowledge I have (m still learning... )....I can only suggest this much ....requesting senior members to help

check if you are connecting to throttle channel and not aileron cause it seems 1st channel...

and binding could be a issue if you are using the tx for first time otherwise there should be no problem

wohaaaaa.....add some heat shrink on the ESC Main wires before u proceed any further
man ...u might endup having burnt electronics....

Yup, will receive them tomorrow, instead i wrapped then will a adhesive tape.

tx and rx are properly bind, that should not be a problem. any idea which slot is for throttle i the receiver ?

usually 3rd channel is for throttel

Convention is
1. Aileron
2. Elevator
3. ESC/Throttle
4. Rudder

But i remember that when a friend got an Avionics 7ch, it was set up differently.
Read the manual to find out which port takes what.

The other issue is polarity. See if the Rx has markings for + & -.
The darkest wire of the three from the ESC is -ve.
See if you plugged it the right way. It will fit even if put in the wrong way.

Without heat shrink tubing be very careful. Put tape properly on all three. If they contact, minimum damage will be a burnt ESC. Maybe a Lipo explosion.

Ok, no sucess yet

Thnx for all yout support, especially Mr.K K Iyer.

off topic,kausha........ i booked a wl v911 from you , its not delivered and the money is returned by your hong kong supplier.
sent many pm to you and you didn't replied. got a pm from you today after a long  long gap, and hope you read my reply also. if you want to say any thing make it public not through pm

Not funny really !
I know you bought a V911 from me, and made the payment through PayPal, but i had some misunderstandings with my supplier and i told the supplier to REFUND your money. I did it almost in a day. I did not cheat you.

I also know you had sent me many PMs and i had immediately replied stating this same problem but in a hurry, it was sent to RcNeil. You can ask him !!

I had not been for a while before some days as my exams were going and so, i messaged you.

As from my side, and the Rubbish reply you sent me was totally immature.
However thanks.

wait dear
i  can post all our pm's regarding the wl v911 here ......be patient


good night .... cu tomorrorow ..... watch this space

Awaiting you.

why you are saying ask to rc neil? i called you many times on your phone but you didn't took.do you know our fellow forum members jaiskj and arunsreelakam.... ( more to the ch.......ted list)......keep going dear ...all the best

santhosh

WHY CANT PEOPLE  BE HONEST ...... THAT TO JUST FOR SOME MARGINAL AMOUNT.....

This is the problem i am facing, pls see.

the motor is damaged it happen to me in my first build and that was very hurting as it was expensive.. and all you can do is buy a new one it is happen maybe because of carelessness while keeping it or any other reason... 

all the best!

Regards
yash

Ok, but are you sure its a motor problem only ? Because HKing told me it should be an ESC problem.

kausha
i am sure the motor is faulty, i have experienced same problem with my quadcopter, finally changed the motor and all is ok

Ok, thnx.

So, heres the replacement motor: http://www.hobbyking.com/hobbyking/store/__25544__hobbyking_bixler_2_epo_1500mm_replacement_brushless_motor_1300kv_.html

But i need to buy in India so that i can receive it early, pls tell from where i can buy the same kind of motor.

Link what you have posted is Bixler 2 motor 1300KV were as for bixler 1.1 2620-1900kv Brushless Outrunner but you can use.

Today got my bixler 2 and i have installed this D2826-6-2200kv.

http://www.hobbyking.com/hobbyking/store/__12919__D2826_6_2200kv_Outrunner_Motor.html?strSearch=2826

please upload a pic of your motor mount then i can suggest you one from LHS..

I am really sorry i could not send the pics, as i had sent the ESC and Motor to RcBanzzar to check, i received them before many weeks, i just had to replace it with a 30A ESC and it would run smoothly.
Now, just yesterday night i fetched out some time and started working on it,
Pls check the pic. I have made it dirty due to the imprints of the gum, thats annoying because a plain whoite looks cool. Now, there's a glitch, i am not able to insert the second screw inside. But i did fit the first screw.
Now, i have glued e back part of the wing because no screw was inserted, for safety, is it ok, should i habe done it ? Or any other method to rectify this.

Thanking you,
Kaushal.