I am very much inspired by the Bruce Stenulson's design. So decided to do a similar one for my first scratch build.
http://www.stenulson.net/rcflight/slimbeag.htm

Since I haven't found similar material, decided to try using the coro

Specification
Wing Span = 36"
fuse = ~28"
Fin and the stabilizer design same as in the link
http://www.stenulson.net/rcflight/woodstok.htm

materials used = coro, balsa strip.

Electronics
Motor - TowerPro Brushless Outrunner 2409-12T
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=2046

ESC - TowerPro H40A
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9299

Servo - Turnigy TG9e 9g / 1.5kg
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9549

Prop - GWS EP Propeller (DD-8040 203x102mm)
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=10046

Batterry - Turnigy 2200mAh 3S 20C
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=8932

AUW w/o electronics = 279grams
AUW w/  electronics = 697grams

How I constructed the wings...

Fuse...

few more...

CG comes somewhere near 40% of the wing with battery in the compartment. is it ok? I made a glide test with battery and no other electronics. It looks fine for me... but while doing 2 / 3 times I feel it is banking little towards right. I'm not sure how I can adjust...

Expecting experts opinion....

Nice Work Bhai... Looking forward for the maiden...

Nice build

Plz elaborate....
CORO.... Is it the same material used for ads???
Plz tell me the thickness of coro?
What glue u hv used?
For joining tail & fuse, stick used is of what???


Thanx for sharing

Rajeev

@Sreedhar: Thank you
@Rajeev: Yes, coroplast of size 3mm, same material used for ads. I have used only hot glue gun in thins build

hi,

chk my pics of the same version.

Its an awesome design Sandeep, Nice perfection... How much is the AUW?
I used only the hot glue gun, are you using any other glue?

Regards,
Dileep

@sbajare  that looks great for a f*v setup.

hey dileep can you share that RC circuit

my email id is

hi,

my auw is 700gms. i use local cyanoacrylate called speedy. never used a hot glue.

regds

superb build sandeep 

can we use coro to make a delta wing rc plane?

Dileep......looks really good. Let us know on AUW, and maiden.

Good luck

Thank you Sandeep. I am also so close to 700grams AUW
@bmblb , I have mentioned the AUW details in the first post . Still doing few modifications / fine tuning while setting up the electricals. Sure, will details all information later...

Regards,
Dileep

But AUW (AUW = All Up Weight) is 976 gm as you have specified dilip in first post.
However, nice build. And you can make wing rib with high density thermocol for better support. But hot glue gun is not ideal, but Bondtite 5 minute epoxy perhaps better. Of course, sanding before applying any glue improve bonding. Use 80 grit sand-paper.

thanks

No kalyan sir, sorry to interrupt, but i think he meant AUW to be 697 grammes including electronic-in first post.
297 gms was its weight without electronics i guess..

Summation for electronics listed comes to be 316 gms+reciever+extra wires, pushrod will make 418 gms.

You seem to have added both..