Moss4X (M4x) : FPV : Giant SPAD GLIDER

Started by rcforall, November 01, 2009, 07:22:26 PM

Previous topic - Next topic

0 Members and 3 Guests are viewing this topic.

rcforall

Here are the First Photos of the MOSS 4X SPAD Glider. ;D ;D ;D ;D

Will Post Specs , Flight Video and FPV Video with OSD display over the next couple of days as time permits, possibly one of the few SPAD  on the world on which FPV has been attempted  ;)  :)  8)

General Details as below :
1) Wing : Span 8ft +
2) Fuse : Aluminum 12 mm Square Tube  with 3 Degree angle of incidence to horizontal for the Wing built in
3) Motor : RCFORALL DY 2820 1000 KV X 2
4) Flight Battery : 2 X RCFORALL 11.1V 4200 MAH ( 1 for each Motor ).
5) AUW : 3500 Gms
6) Props GWS Rotating and Counter rotating 1060.
7) Camera PAL CMOS micro camera
8 ) Avionics RC 500 mW Tx on Board
9) Remzibi OSD
10) 10 dBi Patch Antenna  with 2.4 G receiver
11 ) Fat Shark Goggles .


All this was taken on my  NEW Sony Handy Cam DCR - SX 60  ;D

Flying was Great But had some wing flex  as the wind was high , should sort it out by next week end  :headscratch:

Sai

Note : Saju : With Fuse
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

anwar

:o  ....   :thumbsup:

I hope you did take some video of it one the ground, not just of it taking off !  It would be nice to see it on the ground, up close and personal  ;)  

In fact, this is something that everyone posting videos should do (IMHO).  Just rotate the model in the camera, or take the camera around the model on the ground.  As soon as the model takes off, it is usually too far away to realize the true beauty and any unique aspects of it.
Hangar : Please see my introduction.
RC India forum and me : About this forum.

rcforall

Here is the FPV Video .


Two motors with Rotating Counter Rotating Props  sound awesome like a real plane  especially when when throttle is reduced  >:D >:D

Anwar how do you think up such things  ??? I don't have any stationary ground Video may be next time
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

anwar

Quote from: rcforall on November 01, 2009, 09:22:57 PM
Anwar how do you think up such things  ??? I don't have any stationary ground Video may be next time

I hope you mean it in a positive way  ;)  I was just speaking my mind on what I would like to see; I believe others would also think similarly !
Hangar : Please see my introduction.
RC India forum and me : About this forum.

rcforall

What you said is 200 % right , we normally don't think  such a video is of any use , but from what you say it is logical that it is the only time to get close up to the plane really.
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

rcforall

#5
Here is the edited flight Video of 3 sorties including some close ups in the air.



Sai
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

anwar

This has no ailerons, right ?

How much I wish there were more close up photos or video footage  8-)   :headscratch:
Hangar : Please see my introduction.
RC India forum and me : About this forum.

rcforall

Its 4 channel (ARTE) The earlier version did not  but turning the plane was the  eq. of driving truck with a maruthi steering  ;) :D
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

rcforall

#8
Hopefully sorted out the Wing Flex by running an aluminium Round tube for the entire length as a SPAR  instead of a short length  as a wing joiner .
Should not flex now.

I was thinking of making the Camera and Equipment Tray  as a kind of a reverse aero foil of the wing  below it  for around 6- 8  inches on either side of the fuse .
What I mean is  a mirror Image of the  wings aero foil below the wing  for 6 - 8  " on either side  around the CG Point which is detachable  without  removing the wing . So for that portion it will be a symmetrical wing  for 6 - 8  " on either side of the fuse .
Inside this box the down facing camera/ camera's  , Batteries for the equipment  , OSD  etc  could be Mounted in such a way that  this section can be slid out  something like a drawer of a table  so the wing does not have to be taken out every time the equipment needs to be accessed .

Ref the above Photo 2 of Saju with the fuse where I made  an attempt  that time with a square box type tray and must say it it played havoc with the air flow around that area  so the thought of  converting that tray  a mirror image and making the wing kind of symmetrical .

My only issue is how would the glide and airflow be affected  by  this mod  ??? ???  any idea  
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

rcforall

Finally  was able to  test fly the MODS  made to the  MOSS 4 X  and must say the   the MODS worked great   here is the Video :



The wing flex is  sorted out ,  reverse aerofoiled  Instruments Box  which makes the Wing Kind of symmetrical in the center .

Stability is really great  and the plane now  seems to be a great Low Cost FPV/UAV Platform

Sai
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones

santhosh

will it glide like a twinstar, easystar  with no power
santhosh

rcforall

It glides quite well  as well as the twin star and easy star but not as good as the easy glider pro
www.zuppa.io : vehicle telematics, ADAS, IoT , Drones