In all the model is likely to weigh 1.3 Kgs with everything on board.  Change of motor has been done and it will now me powered by an OS Motor......

l love to watch video  of kaiser

kp

The model is now ready..... Was planned to test fly it today evening but its been raining since yesterday and so am at home.  Here are the few pictures taken over this week.

The first picture ....... that's the under surface of the wing.  Ailerons still to be added.

Second picture onwards the Undercarriage has been added.... the last picture is the top surface of the wing......

a few more pictures.....

The Aileron connections are still to be given in the first two pictures.  The last picture is..... Model - Kaiser Mk I.  Ready and hung on the wall for an appropriate time to fly.  Even tomorrow is expected to be heavy rains..... So let's see when.
The final All Up Weight is 1.3 Kgs.  The model structure made of commercial thermocol has been covered with Butter Paper and then painted using Fevicryl colours.  The the wing surfaces, after the paint job has been covered with transparent masking tape..... normal 2 inch wide tape available in the market.

Great build sir really 

Well the final stats of the Model are....
Wingspan  - 50 Inches
Length      - 36 inches
Weight      - 1.3 Kgs
I am using an OS Motor 3815 - 1000 kv with a 3 cell 2700 mAh Lipo.

Great motor! Pricey though ($ 55 from Tower) but really a great motor

Happy Flying! 

super work there sir, you get to be the winner !! from my side

Well Sanjay Rai Sir.... Got the motor from Sharma's..... most of my logistics is from them.  Old friends and a great family.

rcpilotacro..... Appreciation from your side.... well need nothing more......

Thank you very much.

Today became a rainy day so could not fly it....

That is one fine looking plane sir.. Looking forward to the maiden flight. All the best!

Sir really very nice build of airplane. is that landing gear a bit high , best of luck for the maiden

r u using drawing provided by sharma aeromodel

kp

NIce build sir.

This build is mind blowing

Yes it is the drawling of the Earlier Kaiser which was once upon a time their one of their first few RC models... actually a 3 channel model but I have always flown it as a 4 channel one.  The pictures of the plans put in the first post show it clearly.... This plans dated back to 1982 or 1983 when I first made the model.  I have one copy of it with me.  Guess that is the last surviving one as Sharma's have shifted to the Kaiser Mk II for their production for some time.

Thanks for appreciating the build.... well it is also supposed to give an insight to the budding aeromodellers to take some cues and incorporate them into their model building.  Hope they do it.

i have alo kit and drawing of kaiser mK11 but while building the same by drawing is torned.
furhter do u know which drawing is similar to kaiser mk11 or available online on various sites

Furhter again u are requested guide how u have prepared landing gears of kaiser.


kp 

Well the landing gear of this model is made out of 2.5 mm Duralium Allow sheet i.e. the sheet used to make aircraft skins. I managed some of it somehow.  If your plan for Kaiser Mk II is torn --- just put it upside down on a table and put tape to join the plan.  My old plan has over a dozen pieces of tape stuck to it.

Hey did u buy it from the Sharma's or somewhere else.  You mar try talking to Mr Vivek SHarma and he might send you another plan of Kaiser Mk II.  OR else just go to the Air Wing NCC and ask their Aeromodelling instructor if he has a spare plan of that model.  Being in Chandigarh you should not have any problems.
If you wish to know anything you are welcome...

good 
further u have any notes of learing aeromodelling because in chandigarh i have found no person who can teach me aeromodelling

furhter more, u told that sharma aeromodel help you, but they guys are in jodhpur , how they helped u

next can the said landing gears can be made of aluminum . if yes, give me guidelines along with photo

kp

https://www.facebook.com/groups/310818675629296/

Meet up with this gang who are very active flying very regularly near Sukna

Yes it can be made of Aluminum.....

Rains predicted for the coming weekend... well wished to fly my model.... lets see

Flew my Kaiser today....... it has small issues of setting up the controls to make it fly balanced with no trim.... presently its a slight roll to the left and pitch down.... so the trim setting are slight offset to the right Aileron and nearly full pitch down on the elevator.  Flew twice and did a few aeros..... will trim it today on the work table and fly again maybe in the evening or tomorrow morning and post its videos.

it looks amazing ....could you please the paste link for the plans

it is supplied by sharma aeromodel

kp

Well Rakshit Sharma...... The Sharma Models makes the Kaiser..... but this is the old Kaiser i.e. the Mk I.  You may see my initial posts in the forum to know more and see the pictures of the plan which is a blue print and has been joined at many places.  This plan dates back to sometime in 1981 - 82 when I first made this model.  The present model has some small differences from this one.  The original model is a 3-4 channel Rc model.