Found some 2-3 gram servos too !

Ok so now , all I need is a brushless motor
A propeller
Some servos ( the above ones are too heavy )

+1 To Sahil.

sahil possible some pics of the weighing scale and online links to buy

pictures of the scale i have

some more

 thanks shail ,me too will decide on what rx for micro models for my futaba tx,then willl decide on the rest,shail please pm me on the Motors, lipos, charger, BL motors, BL escs, props which are available locally.

i will post all the links i book marked for myself tomorrow,

bye

Sahil

some LHS links for micro rc stuff

there is also rcbazzar.

http://www.thehobbyshop.in/index.php?main_page=product_info&cPath=12_41&products_id=995
http://www.thehobbyshop.in/index.php?main_page=product_info&cPath=65_11&products_id=602
http://www.thehobbyshop.in/index.php?main_page=product_info&cPath=65_11&products_id=1035
http://www.thehobbyshop.in/index.php?main_page=index&cPath=2_57
http://www.thehobbyshop.in/index.php?main_page=product_info&cPath=16_70&products_id=129
http://www.quadkopters.com/product/716-coreless-dc-motor-high-speed-x-4/
http://www.muav.in/?wpsc-product=linear-servo-1-7gms
http://hobbysea.com/products.php?385&cPath=50&sid=2badd8dd1611eefb9b226d20e032a17a
http://aeroworks.co.in/store/index.php?id_product=77&controller=product

hi roman,

I hope you are still looking to get into micro rc. I got my micro stuff few days back, here are some stuff i got from local electronics market (you can also give it a try in your city).

1. 3.7v 50mah Lipo used in Bluetooth head set (new), these weight about 1.27 -1.35 grams. Rs 38/- x 3no's Rs 40/- x 2no's.
2. micro connectors for usb charger,Rx etc 1.27mm pitch. Rs 20/- each.
3. some low-cost earphones for magnet and coil (31-33 ohms) Rs 35/- each.

Will do extensive testing on battery and earphone coils and post results.

some more pictures.
Note: that USB charger is a fixed 500mah single cell lipo charger, be careful when connecting lipos (check capacity)!

Useful micro-rc links.

1. http://home.comcast.net/~gordon-johnson/batteries.htm
2. http://www.homefly.com/reference.htm
3. http://www.bsdmicrorc.com/
4. I think below link best tells one what is needed/combo n stuff.
   http://www.indoorflyer.co.uk/

Bye
Sahil

Thanks Sahil great info.

can anyone help on how do I make actuators so that I can use them instead of a rudder servo as I am planning to make a micro plane using the parts from a cheap toy heli (inspired by sundaram sir Arun.sreelakam sir and Kalyan sir ) so that I can fly in my building without going to the field.

Below link shows the simplest of all. I will try this and post details here

http://www.instructables.com/id/Wind-your-own-coils-quickly/

Quoteso that I can fly in my building without going to the field.

same here.

QuoteThanks Sahil great info.

I'm happy it was useful. B/w hacked the earphone and got two working coils/magnets but these are drawing quite a bit 110mah@4.1vots/36 ohms   plus very hard to handle, requires a 60watt iron to solder/tin easily.

Hi Sundaram

How much experience do you have with super micro 2.4Ghz 3ch rx, what size coils work(ohms, min. ohms)?.

Sahil

I have not used the super micro at all it was with me brand new.  By the standards of plantraco usage  with an assumption that will not deviate much for super micro too. I would say it's 75 ohms or least 50 ohms coil for actuator. You cannot use the coils of headphone as they are less ohms and too delicate to handle.

I wind my coils on a plastic juice straw. Once required length of enamel insulated wire is wound I spot it liberally with CA. once CA solidifies. I just collapse the plastic straw and draw it out.

Thanks sundaram sir and sahil sir.
@sundaram sir how do i use the coil to make control suurface

Making the actuator coil is nothing but connecting it on a rx and to the control surface and placement of magnet is a delicate work which you have to able to do. Intersting read on them and Video on that

http://www.rcindia.org/servos-gyros-and-all-electronics/making-actuators/
http://www.rcindia.org/electric-planes/diy-micro-flyer-attempt-number-2(400mm-40mhz)/25/

www.youtube.com/watch?v=nNdzsQO7J14

www.youtube.com/watch?v=NPp9Li_fJCc

Second video gives you complete mechanics of how to connect with control surface.

Sir thanks for both the videos.
where can I find micro lipo's like the one used in this build.
how did he connect the actuator to the radio.

and finally where can I find such plans for micro planes.

Update: while I was searching for micro stuff I found something on amazon http://www.amazon.in/s/ref=bl_sr_toys?ie=UTF8&field-brandtextbin=Common+Sense+RC&node=1350380031

Nitesh. I would suggest do some reading yourself too. At least do read all the replies before posting questions after questions. Do some Google search too. Answer to all your question is already in this forum many times over. Even what i have done is just copy paste from this very forum and I am sure if you had searched you would have come across them easily. You will have to get hold of manuals of the specific receiver  you want to use by download and do some reading.

Please don't mind my harsh words since you will learn nothing by spoon feeding. You will learn only by doing it yourself after detailed study.

Of course you are most welcome to ask specific doubt on what you are working at hand. We will be more than happy to learn from what you are doing.

OK sir.

I read a lot about all this, I understood how to connect that actuator to the rx.

Sir just one doubt can I get small lipo's in my local electronic store.

OK sir.

I read a lot about all this, I understood how to connect that actuator to the rx.

Sir just one doubt can I get small lipo's and motors and props in my local electronic store.
The radio and rx I am planning to use is of those cheap toy helis.

For the very same query has  already been answered by Sahil earlier. You can find small lipos in mobile repair shops. Which are used inside bluetooth headsets.

Refer reply #34 earlier