hi
airplane specification
i use 1700 kv motor with 900 mah 7.4volt lipo , prop 8x4 size it is controlled by aileron and elevation , we have throttle , elevator and aileron controls
length is 24 " wing is 32"
using two 9 grm servos and my avionic 7 channel transmitter
also i am using ordinary thermocol which fly everywhere so it cost me nothing
for structure strength i am using wooden rods
no hot wire cutter no proper sending also thats why i do not post any closeup picture
i put lots of tape , my friend call it mummy
that not the brown one which i should use but it is transparent so does not irritate so much but it is everywhere on the airplane.
i am using no plans no downloads nothing
for power weight ratio , i can say it is 1:2 not exactly but approx near to twice the power as compared to its weight that is 260 grms pretty light yaa naaa
which include 9 grm weight of landing gear ,
this time my landing gear is also light last time it was 20 grms approx.
that enough English sorry for spell mistake.
here is the pictures
So what next
flight performance:
today morning as its sun day so i decided to make it my fun day
i start with morning flying i made vertical climb perform two loops few rolls and their after vertical landing
here is the result
wing got broke down i repaired it at afternoon and also i repair inside the motor also see the mounting point i repaired .
mounting of the motor build from coro sheet i mount it using rubber band
landing gear also mounted using rubber band
get back to the flying this evening
here the pic.
@wingmanbunty
Would you like to see ashok baijals biofoam models for quality of build and finish?
Why do you think he got the sweepstakes prize with Sanjay sir?
all i can say about this model
it is fast build but it is not that bad
i think wing should be little smaller
what i think is it is extra light weight
i will make some more improvement in that model
yes sir i had seen that model very nice neat and clean
:salute:
its a fast build i am also preparing my hot wire machine for new build i was just testing this material
Your last post vanished within 5 minutes!
Did you edit it before anyone saw it? But i did ;D
http://www.rcindia.org/electric-planes/fokker-drviii-bipe-sweepstakes-entry/msg178408/#msg178408 (http://www.rcindia.org/electric-planes/fokker-drviii-bipe-sweepstakes-entry/msg178408/#msg178408)
sir
i was busy uploading video on youtube
i remember that airplane post in your biplane build and i got everything so i edited it
sir you know hard work behind building the model inspired everybody and it
makes me (:|~
so here is today evening short take off
https://www.youtube.com/watch?v=WfWvpoAwxKg (https://www.youtube.com/watch?v=WfWvpoAwxKg)
Wow! Great.
This is how videos should be. Short and to the point.
Well done sir!
thanks for support
this model is not final it need lots of improvement today was first testing day .
so i was expecting that :hatsoff:
950 kb
Everybody is flying, except me... BTW, nice bunty saab, nice takeoff.. better suited for carrier takeoff/landings :D
i made some changes in the airplane
hope it will improve the performance
i made dihedral more so that c.g will work for me little bit
done lots of sanding on the wings (60 no paper , 120 no paper and 360 no paper)
covered with brown tape try to improve the wings of airplane for batter lift
flying 300 grm range foamy airplane in 15 mph or above in headwind is little bit
tricky task
i tried to make same situation on simulator , i was able to control the airplane
but on ground situations are really different form the simulator
any tips from the pilots will be of great help. :help:
Quote from: wingmanbunty on September 04, 2014, 01:16:37 PM
flying 300 grm range foamy airplane in 15 mph or above in headwind is little bit
tricky task
i tried to make same situation on simulator , i was able to control the airplane
but on ground situations are really different form the simulator
any tips from the pilots will be of great help. :help:
some time we build model which are so light weighted that when we try to fly them in head wind they are just blown away by the wind to the end of the filed and we have to made emergency landing
it seem nobody was able to reply my post so i search little bit and got
some information , as i am thinking it could be helpful to others in the same situation
(1) make the elevator little downward it will make model to dive the weight of the airplane will work and we lost some altitude but can go ahead in the head wind this is used by glider pilots to fly glider in the
strong head wind
(2)make airplane a little bit nose heavy so that it can perform batter in the heavy winds as i was doing when i was kid and flying kites i used to put small stone at the tail of the kite to make it able to fly in high wind
it seem not good to reply my own post i think little bit , but the second thought came it could help other so why not ,as you can see in the very short to point video my airplane made almost a jump take off
. it does not seem me okay as a designer of this airplane so
i reconsider the design
anybody want to help most welcome.
Its simple.... it is called stability for any object. The more stable it is the better it flies.... the less stable the more drift and other problems come in. Traditionally a heavier nosed aircraft is more dynamically and statically stable than that with a lighter nose.
Your first contention is absolutely wrong. The model must have enough stability and power to fly in the wind. Even in real aeroplanes the same principles apply. A lighter aeroplane gets thrown around in strong winds or turbulence where as a heavier aeroplane flies well even in strong winds. Its all got to do with stability and power available. Yes it does not mean that the aeroplanes have very high thrust to weight ratio... many fly below a thrust to weight ratio of below .5 but are still stable. For gliders read the chapter on Gliding and Gliding in winds. You will understand how it works. Gliders do not have an engine but the Gravity helps them get what is necessary for them to glide.....
Happy flying.
so
today i had done the throttle test of the airplane
here it goes.
https://www.youtube.com/watch?v=8agrrRvcOHk&list=UUGBhSS4hRP6f0xCYMTjc-yA (https://www.youtube.com/watch?v=8agrrRvcOHk&list=UUGBhSS4hRP6f0xCYMTjc-yA)
what changes i should made
because i am planning to test flight it again
what should be expo and D/r
Bunty,
I presume you know dual rate concept.
If in doubt, its like this.
First set the EPA (end point adjustment) so that your servos dont stall at full movement of stick.
This will be 100% on the current DR switch position.
This is the max movement. If you wish, you can reduce it to say 80%
Now turn the DR switch to its other position.
Here reduce the percentage to say 50%.
you can test fly with the DR in LOW.
EXPO
To start with, the control throw is proportional to the stick input.
Expo allows you to change this.
If you set the expo to -20 or -30, the response of the controls will be reduced near neutral, without affecting the total throw.
Depending on your Tx, you can set expo for one or both DR settings.
What i use for a new model is:
1. DR1 50%, expo -20-30% for first test
2. DR2 80%, expo -20-30% after initial test flights
Later i can always set DR2 to 100% and expo to zero!
Caution: check your tx manual for expo setting, whether - or + for soft centre!
i reconsider the design when i see it was drifted away by the wind and vertical fell from the sky
today i made the test flight of the airplane again
this after noon i was charging the batteries i thought lots of responsibilities as everyone would like to see the success part of this airplane
what if anything goes wrong , it doesn't matter to me but this time it happens to me.
my landing gear broke down when i was fitting it in the airplane so on the spot i rebuild a new set of landing gear
when i reach to the field i found no wind at all . it is nil wind condition hardly i got the idea of headwind
https://www.youtube.com/watch?v=EQZvsBR0feg (https://www.youtube.com/watch?v=EQZvsBR0feg)
on takeoff
airplane headed upside i was flying with the expo and D/R so no elevator at all to compensate for that on the spot i flip the switch
(ie on the left side of my tx )its one of the best decision i made as a pilot
i got all the controls at 6 feet above the ground i got all my elevator i headed back to the skies
soon i got all my rudder and aileron the same way , i was flying without any programming.
look i got two friends their to join me
these are rajasthani eagle these are hunter birds using thermals fly very high altitude all i can say about these birds are
perfect killing machine .
so i got lots of them. it did not bother me first i was okay with the situation ,soon it seem to me a dog fight going to start.
it will be batter for me to land so i made a very good approach i used to land at the empty part of the field away from the visitors
so i first cut the throttle to half then i use 25 percent of throttle with very less control inputs
i got very good glide then cut the throttle make a very gentle land on the ground you can see the sound of landing gear touching the ground
just near the end of the video
everybody takes pictures when i reach near the airplane the plane made a perfect landing as you can see in the photo
everybody on the ground has the smiling faces
visitors were happy , i was happy that i am going home with all my electronics and airplane one piece
all thanks to vivek ji, K K Iyer sir and everybody for supporting me
for the success of this project.
the project is over
thanks for joining me.