Will this ESC work with this motor?

prateek13 · January 26, 2011, 08:49:47 PM

just a simple question!

Will this ESC work with this motor?

motor-
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=2140

Model: TR35-36-B
Input Voltage : 7.4V~11.1V (2~3S Li-po)
Kv : 1300rpm/V } within 10%
Nb. of turns : 12 Delta
Max. efficiency current : 15~25A
Current capacity : 35A/30s
Internal Resistance : 42 mohm
No Load current @ 7V: 1.83A
Dimensions : 35mm X 36mm / 1.38in X 1.41in
Shaft diameter : 4mm / 0.16in
Weight : 106g / 3.74oz
Number of poles/magnets : 14
Recommended model weight : 1000~1900g / 35~67oz
Power equivalent : .25 to .30 IC glow engine (400W+)

says Current capacity : 35A/30s

and ESC:-
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=14872

35 amp esc

please help

akky · January 26, 2011, 08:52:40 PM

will advise u to use at-least minimum of 40 amp ....but i would use 55 amps if i were u

SunLikeStar · January 26, 2011, 09:03:03 PM

what prop are you planning to use on it?

akky · January 26, 2011, 09:07:16 PM

9x7 at least master airscrew one or would preffer 11x 6 master airscrew

SunLikeStar · January 26, 2011, 09:10:14 PM

on a 11x6 master it will pull more than 40 amps near WOT, not sure about 9x7.

akky · January 26, 2011, 09:17:30 PM

sorry it was 10x7 n not 11x6

SunLikeStar · January 26, 2011, 09:40:59 PM

10x7 is still not good for this motor, 10x6 or 11x4 will be better choice and you can use a 40A ESC with it. You can run a 10x7 but you'll need a 50A ESC and the motor will run hot.

prateek13 · January 26, 2011, 10:14:41 PM

how about a 9x6?

SunLikeStar · January 26, 2011, 10:22:36 PM

9x6 should be good on 40A ESC.

prateek13 · January 26, 2011, 10:27:44 PM

and any idea how much thrust,power will it create?

SunLikeStar · January 26, 2011, 10:45:54 PM

not sure about the numbers but 10x6 apc is the best prop for it IMO.

prateek13 · January 27, 2011, 10:18:45 PM

a 10x5,10x5.5 will be ok?

SunLikeStar · January 27, 2011, 10:41:33 PM

yep, if 10x6 is ok then 10x5.5 is definitely ok! I'm getting a feeling that you want it to be a slow flyer. If thats the case go with 11x4.

ved · May 22, 2011, 10:12:51 PM

Hi
I wanted to use this motor on a delta flying wing.Please tell me can I use 35A ESC with this motor with 8 x 4 Prop?Please
Motor
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=4321

ved · May 22, 2011, 10:25:51 PM

Please

spitfire · May 22, 2011, 10:30:26 PM

As per the data provided by hobbyking, I dont think there will be any problem using 35 Amp ESC with this motor. In fact as maximum current rating seems to be around 13 amp, 35amp ESC will be only add weight. You can use ESC having rating greater than 15Amp safely.

ved · May 23, 2011, 12:59:04 PM

Thanks