VC Sir,

Any possibilities of offering bigger size models, since I feel more inner space is required for converting the boats into full fledged r/c ones.

Sanjay

Trying my best for a PT Boat of 750mm + length. However, that will take some time. Will keep you posted on that.

Good morning VC Sir...and wwoooowww...for the 750 mm PT boat...sure, you must keep one for me...when arrived...and now i am in happiest mood to assemble the boats...hoooyyy....thank you once again...

All kits have arrived at the Couriers office at Guwahati. I will get them tomorrow. Should be despatching them by the 3rd or 4th latest.

Thank you for your patience.

Good morning VC Sir...and a million thanks for the happiest news..hooraayyy...my heart is pumping with excitement..   its an extreme excitement...

Sir..please consider about the big PT boat...it will be a collection of the lifetime...

All kits have been despatched through Professional Couriers.

Consignment Nos. as follows:

Roopesh - GAU 294519
Ham Aero - GAU 294520
Jana - GAU 294521
Viksi - GAU 294522

Thanks a lot for your interest. Do let me know once they arrive.

Thank you VC Sir..i will collect it from the courier office at Vatakara...

Perhaps, due to an oversight on my part, none of the metal parts (Prop, shaft, stuffing tube and rudder) have been included in the kits as they did not arrive from the manufacturer. I am not sure about this, but I don't recall seeing them as I packed the kits individually.

Would request all those who bought them to please confirm once you open the package. If they are missing, I will send them to you immediately.

My apologies in advance.

VC Sir..if its missing, its need not apology, especially a respected person you.its a silly matter..and i will make it with a ball pen body along with two brass tube pieces..ohh..i am in a sweet dream to make those...yeeaaaa...

Good evening Sir..
i collected the kits from DTDC office by after noon, and it was intact. a million thanks for the kits, is lovely and simple. i will enjoy building those kits after long years of kit building..a million thanks again.

Roopesh, HamAero, Viksi and Jana - Gentlemen, please let me have your mailing addresses once again. The props, shafts, rudders and stuffing tubes have arrived.

Regards,

VC

@roopesh please post the build log for the boats would help me in some way i've also ordered the 39cm boat from him.

i started out the build too. will send out the build snaps in a bit. ( my card reader is missing ) .
question guys , am i the only one who had to trim some of the kits out, also how are u guys gonna drill the hole for the prop shaft ?

Here's my progress so far  

I got some of the trimmings wrong , 1 because i didnt factor in the warp that the wood might have , two i didnt have anything but my eyes for an alignment aid for the ribs.

so ya , the boat is a little warped and im hoping to take care of it during sanding and finishing.

also am thinking of turning this into a sail boat , with a carbon fiber mast and a main sail.
does anyone know where I can get those wench servos ? 

Good evening Friends..first of all i have a humble request to VC Sir..VC Sir, actually these kits aren't cheap boat kits..surely all it are value for money..equally for a beginner and for expert model maker..its too simple to assemble, i took 20 minutes each, but stunning after finish..too stable in water..and flying over water..and i am enjoying my boating with these kits..and i added lots of imagination to each hull, and one is finished as a fishing trawler and one is as a speed boat. i will post all of my building procedure here, within time..and i hope all you also may be building your kits..

Viski, we can simply drill a hole in to any hull, or in to any airframe, by attaching a thin round needle file to 12 mm chuck drill, with speed controller.

here is the basic finish..i will post a detailed log of these boats in time..i also added a dummy engine..still working with decals and lights..

wish you all a nice build..

Regret to inform all concerned that I have cancelled and recalled all the consignments of accessories and a boat kit for Coolprathesh that were being sent through Professional Couriers.

The consignments had been collected more than 3 days ago and I have just found out that they were still sitting at the Couriers office. No reasonable explanation was provided by the staff.

Will despatch them by tomorrow latest. Fresh details will be updated.

My apologies to all concerned and I thank you for your patience. I have sent out individual PM's to all 5 concerned members.

VC Sir..i am waiting for the PT boat kit..with great hope..

not a problem. I know the courier ppl, have being sending couriers myself for some time now. I know how they behave. Professional is not at all professional and DTDC takes money and destroys your consignment.
Do keep me posted about the progress.

All consignments despatched through Blazeflash Couriers:

Roopesh : 2 x (Prop + Shaft + Stuffing tube + Rudder).  Consignment No. 131803288
Viksi :      1 x (Prop + Shaft + Stuffing tube + Rudder).  Consignment No. 131803289
Jana:       1 x (Prop + Shaft + Stuffing tube + Rudder).  Consignment No. 131803290
HamAero: 1 x (Prop + Shaft + Stuffing tube + Rudder).  Consignment No. 131803291
Pratheesh: 1 Boat kit + Adhesives, Sandpaper, Brushed motor Consign. No. 131803292

As per the Courier, expected date of delivery of all consignments latest by Tuesday ( 30th. Aug)

Tracking details should be up here by tomorrow: http://www.blazeflash.net/trackdetail.aspx

Apologies to all for the delay and inconvenience caused.

thanx very much.....

Thank you VC Sir..with those props i can make two more models..

Dear VC,

This is raviteja from hyd, I am new to this forum and I am looking for some ship modeling kits, I use to do in NCC. Is it possible to get Indian Naval ship kits?? apart from regular models you have? Thanks in adv.