Hey guys,
  I got some centre plates laser cut, that can be used to make all kinds of multirotors. (Tri, quad, hex and octacopters) based of the RotorBones Anycopter hub kit.

Pics attached.

Each set of centre plates will cost Rs. 90 + Rs. 70 (Flat rate S&H via EMS Pan-India upto 3 sets) (Discounts available for shipping beyond that. P.M. for further details)

Each set includes the laser cut centre plates ONLY(Top & Bottom Plate, Battery Mount and Boom Drilling Templates)

Booms and Other hardware NOT included. The hub has been designed to use 1/2" booms. Each set will come with a small sheet of paper with photos on the different types of setup possible.

Update: 1/2" Aluminium Booms can be included in the kit @ Rs. 1.5 per inch for custom sizes (kindly specify the size you wish your booms to be    (nominal handling fee of Rs. 30 will be added to the final amount(discounts available for larger orders) ) or Rs. 15 for a standard 12" boom, undrilled(

Hardware Pack Constituting of 18 Stainless Steel M3 x 25 Philips head screws and 18 Regular Nuts also available @ Rs. 90 (No additional shipping charges for it)


Thus total kit can cost as little as Rs. 240 plus shipping for a standard Quad and slightly higher for other variants  

N.B.: Actual hub kit from RotorBones costs $14 which is roughly Rs. 830


Regards
Yashodhan

Is that possible for you to make a custom cut with design given,
also what material is this and how much load can this bear,

Ashok.P

Bump.

@ashok, the material used is 2.5mm pine HDF. It can support a good amount of load and will be stronger once booms are attached , certainly your own designs can be cut as well

Yash, one complete set for a Hexa that will measure 36" from spinner tip to spinner tip. Let me have a quote on this please. Inclusive of 6 aluminium booms, screws and nuts, centre plates etc. Would prefer to have the booms drilled for fitting. Also will need 6 smaller circles of 1.5" dia to be drilled and screw fitted at the tip of every boom (as motor mounts).

Thanks.

A 36"  MtM hex with all that you have asked for would cost you Rs 425+ 100 S&H

The Kit will include:

1. Centre Plates x 1
2. 18" x 1/2" Booms x 6 (predrilled for the centre plates, pls drill motor mounts yourself as per your requirements)
3. 1.5" discs for motor mounts x 6
4. The Hardware pack consisting of 18 M3 Screws and Nuts. (Not enough for motor mounts and motors)

Additional hardware available at extra (special) cost of Rs. 80 for additional sets of screws (18 of each)

   

What is the dia of the centre plate and what length of the 18" boom will be bolted above/below it? I am trying to reach 36" tip to tip, therefore if the centre plate has a 6" dia and 2" of the boom is screwed in then I am left with 16" + 6" + 16" = 38" tip to tip measurements. That suits me fine as I plan on using 10" props.

All else that you have quoted is PERFECT!

The diameter is roughly 5 inches and each boom is bolted 1"  into the centre plates thus giving a tip to tip of 39" 17 + 5 + 17= 39"

Pls. Don't me me cutting you, you said 36" spinner tip to spinner tip, so only if you plan to install half the motor mount on the boom will the 36" tip to tip work, while if you wish to install the entire motor mount you would need an additional .75" (17" boom)  and I chose 18" only because it's in multiples of 1/2 a foot

Thanks will it be possible to let me have 8" dia centre plates and 16" tubes. I would like 2" of tube bolted into the plates.

Or even 8" dia plates and 18" tubes with 3" bolted in will do.

I am really sorry, but 8" centre plates won't be possible

A standard quad kit is available at Rs. 350. INCLUSIVE of Shipping and Handling a Across. India.

The Kit will include:

1. Centre Plates x 1
2. 12 x 1/2" Booms x 4(predrilled for the centre plates, pls drill motor mounts yourself as per your requirements)
3. 1.5" discs for motor mounts x 4
4. The Hardware pack consisting of 18 M3 Screws and Nuts. (Not enough for motor mounts and motors)

Additional hardware available at extra (special) cost of Rs. 80 for additional sets of screws and nuts (18 of each)

   

Rs.350/- for an ARF Quad frame? Yet no takers?

Let me be the first one - One for me please. Will remit in a while.

Sure, will ship it tomorrow/day after. Kindly PM/Whatsapp your address

Anyone interested in the quad kit?
P.S. i am asking this,  so that i can kit them out together.

Need a 2xTricopter center plate and 3xbumble bee motor mount, will send you the template(the same rcexplorer.se david windestal template) by today, PM me your email ID and bank acc no, need a quote on the same with shipping to chennai(Speed post only)

Ashok.P

Bump. Anyone else interested in the quad kit @350/- inclusive of shipping across india ??

is it a 350mm frame?
was wondering if you can make a 450mm?
what's the charge inclusive of shipping?

No. The quad is 27" MtM, that would cost 375/- inclusive of shipping.

Custom Orders Received from "Sidewinder" and "v2_eagle". Will quote prices by tomorrow 9AM

Regards

Update: Pricing revised to 375/- for the Quad Kit, due to certain calculation errors I misquoted @350/-. Pls use the other thread to place orders for the Quad.

Regards

Where is the order thread? I think I sent you pm long back?

Check the post in the sales area just below this one.

Yashodhanp any updates on my/our requests.

Hello, I am sorry for the delay, can you please allow me to give your quotes tomorrow morning first thing?

Please take your time, just thought of reminding you incase you forgot about it.

No no.. My laptop is giving some troubles hanging frequently.