Afro ESC 30Amp Multi-rotor Motor Speed Controller (SimonK Firmware)

Specs:
Current Draw: 30A Continuous
Voltage Range: 2-4s Lipoly
BEC: 0.5A Linear
Input Freq: 1KHz
Firmware: afro_nfet.hex
Discharge wire/plugs: 16AWG/Male 3.5mm
Motor wire/plugs: 15AWG/Female 3.5mm
Weight: 26.5g (Included wire, plug, heat shrink)
Size: 50 x 25 x 11mm

Buy It:-
http://www.rcproduct.in/all-speed-controllers/24-afro-esc-30amp-multi-rotor-motor-speed-controller-simonk-firmware.html

Turnigy 9XR Transmitter Mode 2 (No Module)
9XR Standard Features:
• 8 Channel PPM/9 Channel PCM
• Full Ball Bearing gimbals
• Adjustable Stick Length
• Digital Trims on all Primary Axis
• 16 Model Memory
• Assignable Switches
• Freely Assignable Channel Mixes
• Graphical Dual Rate and Exponential
• Sub Trim and Travel Adjust
• Flaps and Differential
• Throttle Hold
• Supports Heli/ Aero/ Glider Model Types
• Programming Templates Based on Model Type
• Supports M1, M2, M3, M4 stick modes
• 128 x 64 backlit Liquid Crystal Display
• Built in JR & Futaba Trainer Ports
• PPM & PCM Output
• JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc)
• Programmable Timers
• Low Voltage Warning and Buzzer
• Supports 3s Lipo (Required)
• 9XR Firmware Pre-loaded
• AVR ISP Interface
• Internal 2.4GHz Antenna

Spec:
Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD (Backlit)
Support Type: Heli/Acro/Glid
Model Memory: 16
Stick modes: 1, 2, 3, 4
Encoder type: ppm/pcm
Module Interface: JR Compatible (See Related Items Below)
Simulator Interface: Yes (JR & Futaba)
Buzzer: Yes
Battery Compartment: 112 x 44 x 27mm
Weight (less battery & Rf Module): 723g

Required:
Battery 3S Lipo
RF Module

Buy it:-
http://www.rcproduct.in/-24ghz-turnigy-india-/25-turnigy-9xr-transmitter-mode-2-no-module.html



Turnigy 9XR 9Ch Transmitter + Frsky Module

Required:
Battery 3S Lipo

9XR Standard Features:
• 8 Channel PPM/9 Channel PCM
• Full Ball Bearing gimbals
• Adjustable Stick Length
• Digital Trims on all Primary Axis
• 16 Model Memory
• Assignable Switches
• Freely Assignable Channel Mixes
• Graphical Dual Rate and Exponential
• Sub Trim and Travel Adjust
• Flaps and Differential
• Throttle Hold
• Supports Heli/ Aero/ Glider Model Types
• Programming Templates Based on Model Type
• Supports M1, M2, M3, M4 stick modes
• 128 x 64 backlit Liquid Crystal Display
• Built in JR & Futaba Trainer Ports
• PPM & PCM Output
• JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc)
• Programmable Timers
• Low Voltage Warning and Buzzer
• Supports 3s Lipo (Required)
• 9XR Firmware Pre-loaded
• AVR ISP Interface
• Internal 2.4GHz Antenna

FrSky DJT is compatible with JR transmitters following:
JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, PX, 9XII, 11XZERO

Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g

Module specification:
Operating voltage: 6.0V-13.0V (can handle 3S!)
Power consumption: 50mA
Output Power:: 60mW
Resolution: 3072 (11bit)
Dimensions: 63.9x48.5x36.5mm

Included;
1 x 8-channel Telemetry Transmitter Module DJT
1 x Transmitter Antenna
1 x 8-channel receiver V8FR-II (HV Version)

BUY IT:-
http://www.rcproduct.in/combo-offers/8-turnigy-9xr-9ch-transmitter-with-frsky-module-9ch-receiver-mode-2-v2-firmware-combo-offer.html

Hi...Everyone.

Contact us if you have any query or need to ask anything.
You can use Live chat Option also Click below link For LIVE CHAT.

Live Chat:-
http://www.rcproduct.in/chat/client.php?locale=en


OR
Email - rcproduct.in@gmail.com

Turnigy 2650mAh 3S 20C Lipo Pack

The new Turnigy Lipoly packs deliver full capacity at the said C rate.
You wont find a better deal in Lithium Polymer batteries anywhere!

Spec.
Minimum Capacity: 2650mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 225g
Pack Size: 137 x 43 x 17mm
Charge Plug: JST-XH
Discharge Plug: Female XT60

Buy it-
http://www.rcproduct.in/turnigy-lipoly-batteries/19-turnigy-2650mah-3s-20c-lipo-pack.html

Images

FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX

Features:
Advanced Continuous Channel Shifting Technology (ACCST is our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility.
Easy to bind and very fast link-up.
Excellent reboot time.
True Diversity with two antennas.
All channels can be programmed with Failsafe, quickly and easily.
Quick and extremely stable in performance.
Precise and smooth servo response.
Extended range (1.5km-2.5km).

Transmitter Module is compatible with the following transmitters:

DFT:
Futaba: 3PM, 3PK, 7U, 8U,8J,  9C, 10C, 9Z, FN-Series, T10C, FC-18, FC-28.
Hitec: Optic 6, Eclipse 7, Prism 7
WFLY: WFT09, WFT-08

Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g

Buy it OR Read More -
http://www.rcproduct.in/2-4ghz-frsky-accst-india/22-frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.html

ZIPPY Flightmax 4000mAh 3S1P 20C

Zippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!

Spec.
Capacity: 4000mAh
Voltage: 3S1P / 3 Cell / 11.1v
Discharge: 20C Constant / 30C Burst
Weight: 306g (including wire, plug & shrink wrap)
Dimensions: 146x51x22mm
Balance Plug: JST-XH
Discharge Plug: Bullet Connector

Buy it:-
http://www.rcproduct.in/zippy-lipoly-batteries/16-zippy-flightmax-4000mah-3s1p-20c.html

ZIPPY Flightmax 5000mAh 4S1P 20C

Zippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!

Spec.
Capacity: 5000mAh
Voltage: 4S1P / 4 Cell / 14.8v
Discharge: 20C Constant / 30C Burst
Weight: 469g (including wire, plug & shrink wrap)
Dimensions: 143x51x33mm
Balance Plug: JST-XH
Discharge Plug: 4mm Bullet-Connector

Buy Now -
http://www.rcproduct.in/zippy-lipoly-batteries/28-zippy-flightmax-5000mah-4s1p-20c.html

ARF Quadcopter Frame 450mm - Integrated PCB

ARF Quadcopter .

1 x Glass Fiber Quadcopter Frame 450mm - Integrated PCB Version

4 x Brushless Outrunner

4 x 30A ESC

10 x 5 Thin Style E-Prop Black Clockwise Rotation - Turnigy(2pc)

10 x 5 Thin Style E-Prop Black Counterclockwise Rotation - Turnigy (2pc)

1 x Turnigy 2200mAh 3S 20C Lipo Pack

1 x Multi-Rotor Control Board V2.1 (Atmega168PA)

--------------------------------------------------------------------

Quadcopter Frame 450mm - Integrated PCB Version

Features:
Built from quality glass fiber and polyamide nylon.
Integrated PCB connections for direct soldering of your ESCs
Pre-threaded brass sleeves for all of the frame bolts.
Colored arms for orientation to keep you flying in the right direction.
Large mounting tabs on main frame bottom plate for easy camera mounting.
Easy assembly.

Specs:
Width: 450mm
Height: 55mm
Weight: 270g (w/out electronics)
Motor Mount Bolt Holes: 16/19mm
Brushless Outrunner

Specifications:
Model: A28XL
Weight: 75g
Voltage: 11.1v 3s Lipoly
Kv: 890rpm/v
Shaft: 3mm Diameter
Max Load: 30A
Max Watts: 330W
Suggested Propeller: 9047, 1047, 1147
10 x 5 Thin Style E-Prop Black Clockwise Rotation (4pc) [ 2cw and 2 ccw]

Made of nylon, this E-Prop is lightweight and durable. Available in both rotations, it is perfect for your multi-rotor project. Includes adaptors.

Specs:
Diameter: 10 inch
Pitch: 5 inch
Weight: 8.9g
Rotation: Clockwise (From Back)
Color: Black
Turnigy 2200mAh 3S 20C Lipo Pack
Spec.
Minimum Capacity: 2200mAh (True 100% Capacity)
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 185g
Pack Size: 103 x 33 x 24mm
Charge Plug: JST-XH
Discharge Plug: XT60

Multi-Rotor Control Board V2.1

Specs.
Size: 50.5mm x 50.5mm x 23.5mm
Weight: 14.5 gram
IC: Atmega168PA
Gyro: Murata Piezo
Input Voltage: 3.3-5.5V
Signal from Receiver: 1520us (4 channels)
Signal to ESC: 1520us

Whats is a Multi-Rotor Control board you ask?

The HobbyKing Multi-Rotor controller is a flight control board for 4 rotor Aircraft (Quadcopters). Its purpose is to stabilise the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega168PA IC. The Atmega168PA IC unit then processes these signals according the users installed software and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilises your Quadcopter.

The HobbyKing Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega168PA IC via the ail, ele, thr and rud inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

Required:
4 channel or more TX/RX

Buy Now:-
http://www.rcproduct.in/multi-rotors-parts/27-arf-quadcopter-frame-450mm-integrated-pcb.html

Turnigy 9XR Safety Protected 11.1v (3s) 2200mAh 1.5C Transmitter Pack

This battery is designed exclusively for the New Turnigy 9XR radio system.

The pack has both over charge / discharge protection and over current protection built right into the battery, this adds significant safety to the 9xr system.

Spec:
Capacity:  2200mAh
Voltage: 11.1v
Constant discharge: 1.5C (3.3amps)
Max charge rate: 1C (2.2amps)
Standard rate: 0.5c (1.1amps)
Charge cut off: 12.6v
Discharge cut off: 9.0v
Over current cut: 5 amps
Burst discharge: N/A
Weight: 139g
Size: 100x33x19mm
Plugs: JST & JST-XH

Note: This battery is only to be used in Radio Transmitters

BUY NOW
http://www.rcproduct.in/transmitter-lipo-pack/29-turnigy-9xr-safety-protected-111v-3s-2200mah-15c-transmitter-pack.html

Turnigy nano-tech 300mah 1S 35c Lipo Pack (Suits FBL100 and Blade mCPx)
Spec.
Capacity: 300mAh
Voltage: 1S1P / 1 Cell / 3.7V
Discharge: 35C Constant
Weight: 7.6g
Dimensions: 48.5x7.1x19mm
Discharge Plug: E-Flight Ultra Micro

Suited to the following models: E-flite MCP-X

* The nano-core technology in lithium ion batteries is the application of nanometer conductive additives.
1) The nanometer conductive additives form ultrastrong electron-conducting networks in the electrodes which can increase electronic conductivity.
2) These additives create a superstrong ability for imbibition in the carrier liquid to supply more ion channels. This improves the ability of ion transmission and ion diffusion.
Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.
Advantages over traditional Lipo batteries;
-Power density reaches 7.5 kw/kg.
-Less Voltage sag during high rate discharge, giving more power under load.
-Internal impedance can reach as low as 1.2mΩ compared to that of 3mΩ of a standard Lipoly.
-Greater thermal control, pack usually doesnt exceed 60degC
-Thickness swelling during heavy load doesnt exceed 5%, compared to 15% of a normal Lipoly during heavy load.
-Higher capacity during heavy discharge. More than 90% at 100% C rate.
-Fast charge capable, up to 15C on some batteries.
-Longer Cycle Life, almost double that of standard lipoly technology.

Buy Now:-
http://www.rcproduct.in/turnigy-lipoly-batteries/31-turnigy-nano-tech-300mah-1s-35c-lipo-pack-suits-fbl100-and-blade-mcpx.html

4 pcs - Turnigy Talon Alloy Motor Mount Block (Golden Yellow) + FREE SHIPPING

Alloy Motor Mount Block (Golden Yellow)

Buy Now -
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/32-4-pcs-turnigy-talon-alloy-motor-mount-block-golden-yellow.html

Brushless Outrunner 890kv + Turnigy 10 x 5 Thin Style E-Prop Black + Free shipping

Brushless Outrunner 890kv

Specifications:
Model: A28XL
Weight: 75g
Voltage: 11.1v 3s Lipoly
Kv: 890rpm/v
Shaft: 3mm Diameter
Max Load: 30A
Max Watts: 330W
Suggested Propeller: 9047, 1047, 1147
Turnigy 10 x 5 Thin Style E-Prop Black

Made of nylon, this E-Prop is lightweight and durable. Available in both rotations, it is perfect for your multi-rotor project. Includes adaptors.

Specs:
Diameter: 10 inch
Pitch: 5 inch
Weight: 8.9g
Rotation: Counterclockwise (From Back)
Color: Black

You must Need Propaller Mount

Buy Now:-
http://www.rcproduct.in/brushless-motors/33-brushless-outrunner-890kv-turnigy-10-x-5-thin-style-e-prop-black.html

325mm Carbon Fiber Main Blades + Free shipping

450 Size Carbon Fiber blades with reinforced root and balanced tip.

Spec;
Length: 325mm
Weight: 21g each
Grip : 5mm

Buy Now:-
http://www.rcproduct.in/helicopters-parts/11-325mm-carbon-fiber-main-blades.html

This is the same one as in Reply #6, why are you spamming with duplicate posts of the same item ?

Oh...really sorry for that...

I will change it soon..

Multi-Rotor Control Board V2.1 (Atmega168PA) + FREE SHIPPING

Specs.
Size: 50.5mm x 50.5mm x 23.5mm
Weight: 14.5 gram
IC: Atmega168PA
Gyro: Murata Piezo
Input Voltage: 3.3-5.5V
Signal from Receiver: 1520us (4 channels)
Signal to ESC: 1520us


Whats is a Multi-Rotor Control board you ask?

The HobbyKing Multi-Rotor controller is a flight control board for 4 rotor Aircraft (Quadcopters). Its purpose is to stabilise the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega168PA IC. The Atmega168PA IC unit then processes these signals according the users installed software and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilises your Quadcopter.

Buy Now:-
http://www.rcproduct.in/multi-rotor-flight-controller/34-multi-rotor-control-board-v21-atmega168pa.html

200mm Female to Female Jumper Cable Set (10pc)

10 x 1 Pin Female To Female Jumper Cable Set

Only GREEN COLOR Available.

20cm [200mm]

Specs:
Length: 200mm
Pin Spacing: 1mm

Buy Now:-
http://www.rcproduct.in/other-items-and-parts/35-200mm-female-to-female-jumper-cable-set-10pc.html

Hobbyking SS Series 25-30A ESC

Spec.
Weight: 22g
Size: 24x52x6mm
Cells: 2-3S (Auto Detect)
Max Current: 25A
Motor type: Brushless
Burst: 30A
BEC: 3A

BUY NOW:-
http://www.rcproduct.in/all-speed-controllers/39-hobbyking-ss-series-25-30a-esc.html

WLtoys V911 - 2.4Ghz 4CH Micro Helicopter Mode 2 (RTF)

Description:
100% brand new.
Model : V911 2.4GHz 4 channel
Size: 22*8.2cm
Main Blade Length : 19.2cm
Tail Rotor Diameter: 3.6cm
Weight (without power system) : 27.8g
Power supply: Li-polymer Battery 3.7V 120mAh /15C(included)
Flight distance :80-100M
4CH copter Micro Series , 2.4 GHZ overclocking remote control
Function: 3D Omni-Directional flight, rise, fall, forward,backward, turn left, turn right,360 turn left side flying right side flying hover.
Apply to indoor and outdoor flight, over length remote control distance.
Flying stability, easy to operate.
Auto-protection for charging to avoid overcharge.
High capacity battery and strong power motor enable the helicopter to fly much longer and more powerful.
With a USB cable to make charging more convenient.
Excellent flight either indoors or outdoors.

Package included:
1 * 2.4G 4CH RC Helicopter
1 * LCD Display Remote Control
2 * Main Blade
1 * Lipo charger
1 * USB Charging Cable
2 * Li-polymer Battery
1 * Bilingual User Manual (English + Chinese)

Buy Now:-
http://www.rcproduct.in/ready-to-fly-rtf/10-wltoys-v911-24ghz-4ch-micro-helicopter-mode-2-rtf-.html

Every post must have the prices.  Reader shouldn't need to go to your website to find the price

OK,
Thanks For suggestion...
But we can't Provide the Price in the forum for every Item Because some time we have occasionally OFFER And Some Discount for some Products...
So maybe price is changed some times.
So this is the Best way to check the real price on Website.
Thanks

FrSky V8FR-II 2.4Ghz 8CH Receiver (HV)

New FrSKY ACCST (Advanced Continuous Channel Shifting Technology) gives you secure radio communicatios in 2.4Ghz band. ACCST 2.4GHz system shifts 80 channels around hundred times per second in the 2.4GHz band. This means that the system is completely resistant to interference in that band.

Features:
Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility.
Easy to bind and very fast link-up.
Excellent reboot time.
True Diversity with two antennas.
All channels can be programmed with Failsafe, quickly and easily.
Quick and extremely stable in performance.
Precise and smooth servo response.
Extended range (1.5km-2.5km).

Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g

Included;
1 x 8-channel receiver V8FR-II (HV Version)

BUY NOW:-
http://www.rcproduct.in/2-4ghz-frsky-accst-india/40-frsky-v8fr-ii-24ghz-8ch-receiver-hv.html

Recently bought a Radio and RX from RC Product. Excellent overall service and really good packaging ( in courier / ems). I was very apprehensive to start with but, Mehul the joint owner called and updated and on each stage of the order.

Thanks you all at rc-product and please continue giving such good service to the community.

Thank you Very much...

Turnigy 1000mAh 2S 30C Lipo Pack

Spec.
Minimum Capacity: 1000mAh
Configuration: 2S1P / 7.4v / 2Cell
Constant Discharge: 30C
Peak Discharge (10sec): 40C
Pack Weight: 64g
Pack Size: 75 x 34 x 12mm
Charge Plug: JST-XH
Discharge plug: XT60

Buy Now:-
http://www.rcproduct.in/turnigy-lipoly-batteries/37-turnigy-1000mah-2s-30c-lipo-pack.html