HobbyKing 50watt 5A X-Charger/Balancer

Microprocessor controlled
Delta-peak sensitivity (NiMH/NiCd)
Individual cell balancing
Li-ion, LiPo and LiFe capable
Ni-Cd and NiMH capable
Store function, allows safe storage current
Fast charge Function
Data store/load
Backlit LCD
Internal resistance checker

Operating voltage range: 10.0~18.0Volt
Circuit power: max.50W for charging, max.5W for discharging
Charge current range: 0.1~5.0A
Discharge current range: 0.1~1.0A
Current drain for balancing Li-po: 300mAh/cell
NiCd/ NiMH battery cell count: 1~15cells
Lithium battery cell count: 1~6Series
Pb battery voltage: 2 to 20V
Dimension: 135×100×40mm
Power Supply Not Included.

Buy Now-
http://www.rcproduct.in/other-items-and-parts/42-hobbyking-50watt-5a-x-chargerbalancer.html

Turnigy Talon Carbon Fiber Quadcopter Frame
The Talon features a beautifully finished carbon fiber main frame and arms, all connected together with aluminum alloy parts. This frame really gives your quad a high-tech and quality look.

We also offer a full line of quad electronics such as quadcopter control board, ESC, motors and more, so it has never been easier or more affordable to get a quad in the air!

All necessary hardware is included.

Specs:
Weight: 240g
Width: 498mm
Motor Bolt Holes: 22~32mm

Buy Now:-
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/38-turnigy-talon-carbon-fiber-quadcopter-frame.html

ZIPPY Flightmax 5000mAh 4S1P 30C

Spec.
Capacity: 5000mAh
Voltage: 4S1P / 4 Cell / 14.8v
Discharge: 30C Constant / 40C Burst
Weight: 526g (including wire, plug & shrink wrap)
Dimensions: 149x51x37mm
Balance Plug: JST-XH
Discharge Plug: 5.5mm Bullet-Connector

Buy Now:-
http://www.rcproduct.in/zippy-lipoly-batteries/48-zippy-flightmax-5000mah-4s1p-30c.html

ArduPilot Mega 2.6 + External Compass w/Ublox NEO-6M

The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

Features:
- Arduino Compatible!
- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- Optional off-board GPS, uBlox LEA-6M module with Compass.
- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

GPS Features:
- Built-in compass GPS module
- Main chip: Ublox-6M
- With fast satellite searching speed and high precision
- Compatible with APM serial port and I2C port
- Includes round plastic shell and GPS support

Package Included:
- APM 2.6 Board w/Shell
- Ublox-6M GPS module w/Round plastic shell
- GPS folding support

Buy Now:-
http://www.rcproduct.in/multi-rotor-flight-controller/51-ardupilot-mega-26-external-compass-wublox-neo-6m.html

500 Series 3D Electric Helicopter Combo KIT [ARF] - Turnigy Typhoon 1800kv ,Turnigy Metal gear Servo

Items Included In COMBO PACK.
500GT 3D Electric Helicopter Kit:-
Features.
Light weight design provides awesome flight performance and extreme 3D capability.
Rotor head/tail with thrust bearings.
Direct-to-swash CCPM linkage.
Center of gravity of battery tray designed close to the rotor head.
High efficiency belt driven tail.
Fully driven tail auto rotation system.
Tail servo boom mount.
Carbon Fibre boom support rods.
High rigidity 2024 alloy main frame.
Specification:
Length: 840mm
Height: 310mm
Main rotor diameter: 970mm
Tail rotor diameter: 200mm
Motor pinion gear: 13T
Main drive gear: 162T
Tail drive gear: 31T
Drive gear ratio: 1:12.46:4.68
Weight(without power system): 1370g
Flying weight: Approx 1700g

Turnigy Typhoon 500H Heli Motor 1800kv (500 Class):-
Specifications:
Dimension: 37mm x 50mm, 71mm(with shaft)
Weight: 170g
Kv: 1800rpm/V
Voltage: 3-6S
Max current: 55A
Diameter of shaft: 5mm
Length of front shaft: 20mm
ESC: 65A
A serious upgrade for any 500 size heli.

70A BlueSeries Brushless Speed Controller:-
Features:
Extremely low internal resistance
Super smooth and accurate throttle linearity
Over heat and over-load protection
Auto shut down when signal is lost or radio interference becomes severe for more than 2 seconds
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched ON)
New Advanced programming software

Programming features:
Brake setting (we recommend using brake for only folding props applications)
Battery type(LiPo or NiCd/NiMh)
Low voltage cutoff setting
Factory default setup restore
Timing settings (to enhance ESC efficiency and smoothness)
Soft acceleration start ups (for delicate gearbox and helicopter applications)
Governor mode(for helicopter applications)
Motor rotation( clockwise\counterclockwise)
Switching frequency
Low voltage cutoff type (power reduction orirnmediate shutdown)

Factory default settings:
Brake:  off
Battery type Detect:  LiPo with Automatic Cell
Low voltage cutoff threshold:  Medium (3.0V/65%)
Timing setup:  Automatic
Soft Acceleration Start Up:  Medium
Governor mode :  OFF
Frequency :  8kHz
Low voltage cutoff type:  Reduce power

Spec.
Cont. Current: 70A
Burst Current: 90A
Battery: 2-6 Cell Lipo / 5-18 Cell Ni-XX
SBEC: 5.5V/ 4A Output
Size: 57*31*12mm
Weight: 53g

401B AVCS Digital Head Lock Gyro:-
Functions:
Compatible with both Digital and Analog systems
Minimizes rudder trim changes caused by wind, other meteorological changes, and varieties of helicopter attitude changes are automatically cancelled.
Sensor vibration proofing
Simple sensitivity adjustment

Specifications:
Digital proportional RIC system
Operating voltage: 4.8V ~6V( common for receiver)
Operating temperature: -lOL r-.rf-45 C
Dimensions: 28x26x20 mm
Operating current: 80mA

Turnigy S3317M Servo 26g / 3.0kg / .14sec:-
Turnigy S3317M Servo  26g / 3.0kg
Weight: 26g
Dimensions: 42 x 28 x 15mm
Torque: 3.0kg-cm
Speed: .14sec
Gear Type: Metal

Required:
6 channel or more radio system (transmitter & receiver)
4S 14.8V 2200mAh lipoly battery or 6s 22.2v 2200mah

BUY NOW:-
http://www.rcproduct.in/combo-offers/9-500-series-3d-electric-helicopter-combo-kit-arf-turnigy-typhoon-1800kv-turnigy-metal-gear-servo.html

RCpro (v1.0) Quad-copter Frame (500mm)

RCpro (v1.0) Quadcopter frame is a crafted from high quality genuine carbon fiber and Glassfiber ARMS offering both great looks and performance.

RCpro (v1.0) has Carbon Fiber Main Top Plate and Bottom plate.

12mm OD Glass fiber Arms with Motor Mount.

Item Included :-

    4 x DIY Round Tube Motor Mount (12mm Tube)
    4 x Alloy Mount Block (Golden Yellow)
    Hardware Package (complete)
    1 x Carbon Fiber Main Frame Upper Plate
    1 x Carbon Fiber Main Frame Lower Plate

Buy Now [More information] :-
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/52-rcpro-v10-quad-copter-frame-500mm.html

4pcs - Turnigy 10 x 5 Thin Style E-Prop
Made of nylon, this E-Prop is lightweight and durable. Available in both rotations, it is perfect for your multi-rotor project. Includes adaptors.

Item Included

2 x Clockwise
2 x Counterclockwise

Specs:
Diameter: 10 inch
Pitch: 5 inch
Weight: 8.9g
Rotation: Counterclockwise And Clockwise(From Back)
Color: Black

Buy Now :-
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/56-4pcs-turnigy-10-x-5-thin-style-e-prop.html

ArduPilot Mega 2.6 + External Compass w/Ublox NEO-6M [Side PIN] Re-Stocked

Buy Now:-
http://www.rcproduct.in/multi-rotor-flight-controller/51-ardupilot-mega-26-external-compass-wublox-neo-6m-side-pin-.html

Following Items Are Re-Stocked

Turnigy 1000mAh 2S 30C-40C Lipo Pack
http://www.rcproduct.in/turnigy-lipoly-batteries/37-turnigy-1000mah-2s-30c-lipo-pack.html

FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX
http://www.rcproduct.in/2-4ghz-frsky-accst-india/22-frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.html

Open LRS 433MHz Transmitter 1W + Open LRS 433MHz 9Ch Receiver
http://www.rcproduct.in/combo-offers/50-open-lrs-433mhz-transmitter-1w-open-lrs-433mhz-9ch-receiver.html

m waiting for 6ch radio

ok...I will inform you once i have stock of 6 ch.

Turnigy 1000mAh 3S 30C-40C Lipo Pack

The new number one in performance and price!
The new Turnigy Lipoly packs deliver full capacity at the said C rate.
You wont find a better deal in Lithium Polymer batteries anywhere!

Spec.
Minimum Capacity: 1000mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 30C
Peak Discharge (10sec): 40C
Pack Weight: 89g
Pack Size: 75 x 33 x 19mm
Charge Plug: JST-XH
Discharge plug: XT60

Buy NOW -
http://www.rcproduct.in/turnigy-lipoly-batteries/36-turnigy-1000mah-3s-30c-40c-lipo-pack.html

FREE SHIPPING FOR ArduPilot Mega 2.6 + External Compass w/Ublox NEO-6M

Buy Now:
http://www.rcproduct.in/multi-rotor-flight-controller/51-ardupilot-mega-26-external-compass-wublox-neo-6m-side-pin-.html

Mobius ActionCam a 1080p HD Video Camera Set With Live Video Out

The Mobius ActionCam is the natural progression of the ever-popular 808 key chain camera. The developers of the 808 and the open source community came together to create a more capable 1080p level of hardware, but keeping what made the 808 cameras so great; small, lightweight, configurable and of course great video at a low cost.

The Mobius has been embraced by the DIY and Open Source community, pushing the ever growing software envelope and coming up with new ways to use the Mobius, such as different lenses and ribbon cables to relocate the camera section. The Mobius can even be reconfigured, settings changed and firmware updated using the free computer GUI software.

The Mobius camera is quickly becoming the go to camera for the RC community, with its low cost, video out capability for FPV use, superb HD video recording and DIY configurability. It is a great all-around action camera with a host of accessories and mounting options, for a wide range of applications.

Features:
• Three user selectable video modes, 1080p-30fps or 720p-60fps or 720p-30fps
• Three movie quality settings (super, standard, and low)
• Five video recording cycle time settings-3, 5, 10, and 15 min and max
• Loop Recording
• Movie Flip (180 deg. rotation)
• Movie Sound allows turning off the sound and eliminating a sound track from a video
• Photo capture mode with frame sizes of 2304x1536, 1920x1080, or 1280x720
• Time Lapse photos of .25, .5, 1, 2, 5, 10, 30 and 60 second intervals.                 
• Recording LED toggle flashes the recording mode LED on the top and rear of the camera.
• Movie/photo time stamp toggle
• Power on button delay (to prevent premature activation while handling)
• Auto-record when power to the camera is applied (useful for dashcam use - no button presses needed.)
• Charging on/off toggle when plugged into a USB data port (useful for some external USB devices)
• TV out (PAL or NTSC), which includes a playback mode with audio.
• TV display ratio (4:3 or 16:9)
• GUI program for Windows OS for easy setting of the parameters as well as updating the firmware

Specs:
Video format: 1080p HD @ 30fps, 720p HD at 60 or 30fps
Battery: 520mah
Video storage: Micro SD Cards up to 32GB
Weight: 39g (camera only)
A/V live out: Audio and video out available

Included:
1 mounting sleeve (base) with 1/4"-20 thread for tripod use
USB cable
1" Hook and Loop tape

Buy Now :-
http://www.rcproduct.in/fpv-camera-monitor-audio-video-txrx/62-mobius-actioncam-a-1080p-hd-video-camera-set-with-live-video-out.html

APM Power Module with XT60 Connectors and 6 Pin 150mm Cable

All thru a single and tightly included 6-pin cable that directly matches the HKPilot's connector. The on-board switching regulator outputs 5.3V at a maximum of 2.25A, and can be used up to 18 Volts (4S LiPo) and at a maximum of 90 amps. The Power Module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection.

Note: The Power Module is rated at 2.25 Amps to power the HKPilot, receiver and peripherals (GPS and Telemetry radio) ONLY. To power servos use an ESC with an adequate BEC or a standalone BEC plugged into the output bus, and remove jumper 1 to isolate the two power lines.

Specifications:
Max input voltage: 18V
Max current sensing:90A
Switching regulator outputs: 5.3V at 2.25A max
6-pos Molex cable plugs directly to HKPilot
Voltage and current measurement configured for 5V ADC

Includes:
DF13 6 Position Connector 150mm long
APM Power Module with XT60 Connectors

Buy Now :-
http://www.rcproduct.in/multi-rotor-flight-controller/65-apm-power-module-with-xt60-connectors-and-6-pin-150mm-cable.html

RCP - 4 Axis Quadcopter Folding Frame Kit

Features:

- This is a new folding copter quadcopter Designed for professional FPV system
- 16mm thickness tube.
- Axis distance 700mm
- Adopts high strength material,CNC processing
- High Wind resistance design,low power consumption,support most flight controller board    
- All the arm tube with standard hole, and easy to assemble
- Compatible with Single Axis or two- axis PTZ
- Net weight: 650g
- Package weight: about 1000g
- Not include any power or electronic devices

Recommend configuration(not included):

- 4 x Motor
- 4 x ESC        
- 4 x Propeller [11inch]
- Battery: 4S/5000
- Flight control:  APM2.6 with GPS

Buy Now -

http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/66-rcp-4-axis-quadcopter-folding-frame-kit-.html

Turnigy 9X Transimitter LCD Backlight Kit - Green (DIY)

Ever wished your Turnigy 9X transimitter had a backlit LCD?
Wish no more! the Turnigy 9X LCD backlight kit is here!
Other solutions require soldering or use a noisy inverter, voiding CE and warranty. However the Turnigy LCD Backlight Kit is LED driven and is a snap to install!

No soldering is required, you can do this simple upgrade yourself.
If you can use a screw driver you can install this backlight!

Specs:
Input Voltage: 8v - 13v
Current Draw: 60~90mA
Color: Green

Buy Now:-
http://www.rcproduct.in/-24ghz-turnigy-india/67-turnigy-9x-transimitter-lcd-backlight-kit-green-diy.html

1.2G 1W [1000mW] Wireless Audio/Video Transmitter+1.2G 15Channel Audio/Video Receiver Set

Transmitter specification:

Channels: 15
Voltage: DC 12v
Current Draw: 200mA
Power Output: 1000mw
Weight 30gram (without antenna)
Size: 85mm x 50mm x 19mm
Antenna out: SMA (Antenna included)

Receiver Specifications:

Channels: 15
Voltage: DC 12v
Current Draw: 200mA
Current:350mA
Video Output: 75ohm Impedance via RCA (Cable included)
Audio Output: 10kohm Impedance via RCA (Cable included)
Temperature: -20℃---+60℃
Size: 80mm x 60mm x 20mm
Antenna out: SMA (Antenna included)

Buy Now :-
http://www.rcproduct.in/fpv-camera-monitor-audio-video-txrx/69-2g-1w-1000mw-wireless-audiovideo-transmitter12g-15channel-audiovideo-receiver-set.html

Carbon Fiber FPV Convertable Quadcopter Frame Kit (White+Black Motor Mount)

REALLY BIG...!!!

Specification:
- Material:ABS(Center Board) + Carbon fiber(Arm)
- Color:black + (White+Black Motor Mounting Plate)
- Length:870MM
- Weight:310g
- Package weight:440g

Package includes:
- 4 x Arms
- 1 x Upper cover plate
- 1 x Lower cover plate
- 1x Screw (one bag)

You can Make 4 Different pattern with this Frame.

  * QuadCopter
  * TRICOPTER
  * Y - COPTER
  * REPTILE.

- Suitable for DIY use,you can choose a proper Landing skid gear and camera mount gimble to DIY your own unique quadcopter!

- You need Servo / Tail Mechanism For Making Tricopter or Y Copter.

BUY Now :-
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/70-carbon-fiber-fpv-convertable-quadcopter-frame-kit-whiteblack-motor-mount.html

The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you're ready to go! All of which is done with easy to follow on screen prompts!

The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1.5 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.

The KK2.1.5 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap.

If you're new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1.5 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.

Specs:
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us

Firmware Version: 1.6:
Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S

Buy Now -:
http://www.rcproduct.in/multi-rotor-flight-controller/71-kk215-multi-rotor-lcd-flight-control-board-with-6050mpu-and-atmel-644pa.html

Re-Stocked -

APM 2.6 + External Compass w/Ublox NEO-6M .
http://www.rcproduct.in/multi-rotor-flight-controller/51-ardupilot-mega-26-external-compass-wublox-neo-6m-side-pin-.html

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) + ZIPPY Flightmax 2500mAh Transmitter Pack (Futaba/JR)
http://www.rcproduct.in/-24ghz-turnigy-india/46-turnigy-9x-9ch-transmitter-w-module-8ch-receiver-mode-2-turnigy-2650mah-3s-1c-llf-tx-pack-futabajr.html

FPV Mini 5MP HD 1280x960 Camera with Mic Audio and video Output for Photography and Video [600TV Line]

Specifications:
- Sensor: 1/4'' HD Sensor
- Resolution: 1280x960
- Pixel: 5MP
- Definition: 600TVL
- Minimum lux: 0.5Lux
- SNR: >48db
- Gamma: 0.45
- Electronic shutter: PAL;1/50'1/100,000s NTSC:1/60'1/100,000s
- Work voltage: 5-9v [USE BEC or UBEC or 2s lipo]
- Work temperature: -40~+85℃
- Auto white balance
- Single track audio output
- Video output: 1vp-p75ohm
- Color

Buy Now -
http://www.rcproduct.in/fpv-camera-monitor-audio-video-txrx/73-fpv-mini-5mp-hd-1280x960-camera-with-mic-audio-and-video-output-for-photography-and-video-600tv-line.html

APM2.6 [ArduPilot Mega 2.6] Kit - Flight Controller Board for Multicopter - Side PIN - ONLY APM 2.6

This is the new APM 2.6 autopilot module. The sensors are exactly the same as with APM2.5+, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.

The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

Features:
- Arduino Compatible!
- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- Optional off-board GPS, uBlox LEA-6H module with Compass.
- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

Package Included:
- 1* Side Pin APM2.6 Board
- 1* APM2.6 Shell
- Cables

Not Included:
- GPS + External Compass

Buy Now-
http://www.rcproduct.in/multi-rotor-flight-controller/75-apm26-ardupilot-mega-26-kit-flight-controller-board-for-multicopter-side-pin.html

Quadcopter Power Distribution Board

Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring.

Features.
Power Input: XT60 with 12AWG wire
Motor output: 4 x 3.5mm Female bullet plug
Aux output: 2 pin JST compatible
Weight: 27.3g (including wires)

Buy Now:-
http://www.rcproduct.in/multi-rotor-arfkitrtf-and-pare-parts/76-quadcopter-power-distribution-board.html

Following Items are Re-Stocked...

ArduPilot Mega 2.6 + External Compass w/Ublox NEO-6M [Side PIN]
http://www.rcproduct.in/multi-rotor-flight-controller/51-ardupilot-mega-26-external-compass-wublox-neo-6m-side-pin-.html

APM 2.6 + Ublox NEO-6M GPS With External Compass + APM POWER MODULE - [COMBO OFFER]

http://www.rcproduct.in/combo-offers/74-apm-26-ublox-neo-6m-gps-with-external-compass-apm-power-module-combo-offer.html