hello guys if any interested in buying this can contact me this kit is 100% original.We directly import from dealer so they are quite cheap.One kits cost u guys 8250 inc shipping.if u want discusses about the price pls fell free to contact.For bulk order prices will be low  

The package include:
1pcs Robocat 270 Carbon Fiber Quadcopter

1pcs Naze 32 Flight Controller Board

1pcs Esc Connection Board  

4pcs 2204 2300KV Brushless Motor

4pcs Emax 20A Simonk ESC

8pcs 5030 propeller (2 pairs black 2 pairs green )

Product Description

Robocat 270mm RC 4 Axis Quadcopter
Robocat was designed with aero dynamics in mind.
The carbon fiber we use allows us to create a sturdy but light weight structure .
For the Canopy we took into account the ease of maintenance. The design incorpo-rates a hinge feature allowing for easy access to the electronic insides.
An eye-catching form paired with a streamlined canopy, high speeds are achievable due to the low drag. The Canopy comes in different colors suitable for various situations . The Canopy is made from shock-absorbing PC material.
If you have FPV racing on your mind ,then this is the number one quacopter for you.
Naze32  Flight Contorl Board

36x36 mm
5.3 grams (no headers, 7.3 grams with)
2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6050)
3-axis magnetometer (HMC5883L)  
Pressure sensor (MS5611)  
Flexible motor outputs, support various airframe types -
Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum Satellite receiver.
Battery voltage monitoring
Modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
16Mbit onboard SPI flash
Onboard MicroUSB for setup and configuration
LEDs so bright, they will blind you
MultiWii-based configuration software for easy setup
rev v2.3 hardware
please use the Chrome Baseflight Configurator for the GUI. DO not use the old 2.2 GUI!

STM32 - 32bits!
MPU6050 (Gryo/ACC)
HMC5883L - (Mag)
MS5611 - (Baro)
Photo Quad-X-flip2_zps20c7c54b.jpg
awesome Flip32 Manual download . thank you  RC JOSEB

RcInput order: Roll,Pitch,Throttle,Yaw,Aux1,Aux2,Aux3,Aux4

GV to RT = GND VIN RX TX
Gv to CD = GND VIN SCL SDA


Mixer Example settings:
#mixer tri → Tricopter
#mixer quadx → Quadrokopter in X configuration
#mixer hex6x → Hexacopter in X configuration

#feature ppm ( activate PPM Reciever)
#feature-ppm ( traditinal reciever)
To change the channel order, here is a example:
#map EATR1234
EATR means:
Elevator
Aileron
Throttle
Rudder
1234 are the channels
if you are finished you have to save the settings type :#save

Setup your radio to be 1000-2000 and midstick exactly 1500 (this all can be changed of course but this is easy to do)

Go from the gui in the cli and do following commands
set mincheck = 1020
set maxcheck = 1980
set looptime =3000
set mincommand = 1000 <--as calibrated
set maxthrottle = 2000 <-- as calibrated
set minthrottle = 1100 (This is throttle after arming and offcourse this is different on every motor or ESC so adjust for your taste)

 LE TODAR 2204  2300KV Brushless Out runner Motor  

this is a great motor with  tons of advantages. Never heats up after a few mins of testing, you can barely feel the heat. They are designed with one thing in mind - maximizing Multi-rotor performance! The new motors are the new standard in Multirotor performance. Each motor is built for a specific type/application allowing for further refinement and efficacy/power to be optimized. Built using the highest quality components from Japan bearings, n45sh Magnets, .2mm laminations, 180deg oxygen free copper wire, .005g balancing, and then the design of each motor are also evaluated for their type application and everything from their mounting, to the prop type adapters are taken into consideration. he lower motor frame is chamfered for easy fitment on tighter frames and has plenty of height for mounting hardware to wingding clearance. Runs on 2-4s (keep that prop at 5" for 4s!) and will provide smooth, reliable power. And lots of it.
It might have to do with its height which is about 3mm higher than the other one. Also the flat base is quite interesting, I used to have problem that the shaft and C-clip rub into motor mount or something else when it didn't line up. This one all you need is the right 16/19mm mounting holes and no more worries about lining up!!.
Thick semi hollow shaft for good stiffness while remaining lightweight
Interchangeable propeller adapter for both traditional propeller and thin CF propeller
Flat motor base eliminate the need of shaft hole on any motor mount
Heavy duty to take a crash and keep going
Power con paired to sunnysky 2300k
Bearings are 5x9x3 (MR95ZZ).
490g of thrust with HQ 5x4 at 10.5A / 130W !  
Bolt on style prop - 2 styles  spinner and 2 blade CF adapter included
Shalf: M5
Bottom mounting Holes : 16mm*19mm 3m