Hey guys,

I have 4x new skyzone TS5828 5.8G 600mW vtx for sale.
Price(for each)- Rs.1600 including shipping via EMS.

AND

I have 3x new skyzone TS5823 5.8G V2 200mW vtx for sale.
Price(for each)- Rs.1250 including shipping via EMS.

All the video transmitters will come with a Heatsink Kit Included which consists of:
1) 2gm heatsink
2) Thermal silicone heat pad( pre-applied to heatsink)
3) Heatshrink tube  


Note-
1) Please power the vtx with the antenna connected always.

2) Maximum input power for these vtx is 12V(3S). Powering it with an input voltage higher than this will heat it to the point that it will fry it. It is recommended to use a12V BEC to power it.

3) Double check all connections before powering.

I am not responsible if the the vtx is damaged by negligence on the part of buyer. What i have mentioned should be followed strictly to reduce the chances of damaging the vtx.  

Pic #2- Whats in TS5828(600mW) box.
Pic #3- Whats in TS5823(200mW) box.
Pic #4- Heatsink kit.

Note-
Inside the box pics are taken with my own units none of the new boxes were opened.

*this sale is only to help me sustain myself in the hobby if you buy an rx from me i thank you sincerely
Please do not bargain i have set the prices according to what each unit cost me.

Heat Sink mod(Mini How To)

The heat-sink mod helps the vtx by allowing it to have more surface area to dissipate the heat. These tiny vtx get hot after some time of use and to prolong its life keeping the heat-sink under the maximum operating temperatures will help it significantly.

The heat-sink mod will add some weight and height to your vtx, if your build has minimal space then you may opt not to do it.
But it is highly recommended to do it on the TS5828(600mW) or atleast ensure that your vtx is placed on your craft in a manner that it receives good airflow over it.

(Open image in new tab for a bigger pic)



Heat-sink kit contents.

First Step-Cut the shrink wrap on vtx carefully, ensuring that you dont damage the pcb.



Remove the sticker.



Now you should have the exposed module casing.



If you like you can cut the pin out part of the sticker and place it where you like for convenience.



Now take the heat-sink and carefully remove the plastic protection film on the flat side.



Now you should have the exposed thermal pad.



Carefully place the heat-sink approximately in the center on the module casing with the thermal pad facing down and press firmly.



This is how it should come out.



Now slide the vtx into the heatshrink tube and apply heat with a lighter or heat gun. Adjust as required so the heatshrink covers the vtx properly.



Now cut the heatshrink around the DIP switch and connector.( TS5828 in pic, placement of connector is different in TS5823)



Now you should have the vtx with the finished heat-sink mod.

1x TS5823 sold.
Cheapest prices for these vtx anywhere in india, grab em while they last.

one 200mw vtx for me
whatsapp 9782324030

Anymore 200mw left.
Please ping me @8123500484

Update:
All 200mW sold, thanks guys.

4x 600mw remaining

1x 600mw booked.

Bump!

I will buy 600mw one

Sent from my ZUK Z1 using Tapatalk

3x 600mw available. 1x booked

Price for all 4 600mw units: Rs.6000 including shipping.

Bump!

3 pieces 600mw available.

Still available, the price for the 600mw may be slightly steep than ordering from intl. sites but i have incurred 41% customs per unit and the pricing only reflects this not making any profit on them.

3x 600mw available.

Bump!

600mW-4 pieces available currently.

600mW available.

Revising price for:
TS5828 600mW- Rs.1500 including shipping.

Bump!

Can you get a reciever as well?

Hey francisoran sorry dont have receivers in stock.

Bump! No interest in 600mW?

2 pieces 600mW sold.

Only two remaining,
1 piece- Rs.1500 including shipping.
2 pieces- Rs.2800 including shipping.

Book one for me..