i have a helicopter and need to reduce its weight so that it can lift itmes with it suggest me how can i do so
i have a project to submit so need too reduce its weight
Joker,
please elaborate on the topic, like which model do you have and the weight of the object you wanna lift
Try VLCC !!
Quote from: VMaliakal on March 24, 2012, 02:07:38 PM
Try VLCC !!
:rofl: :iagree:....
fast heli when on fast looses weight fast; let her fast. :giggle:
remove all unwanted lights, remove landing skid, remove all stickers.. and replace a new battery half in capacity, and place it in to little front in order to maintain Center of Gavity.. removing caopy can make some flow disturbances in down wash, makes it erratic..
its basically a chinese helicopter..........
of medium size....
and need to lift around 400gms on it a camera and a motor..............
can u help me how to do so
Please specify the size n the make n battery, motor used in it.......400gms is a lot of weight....
its volitation helocopter
has 3.7 v battery and of 1300mah
battery
need to lift a cam a 9 volt battery and a motor to control motion of camera
Reduce battery mAH and increase C Capacity.
Definitely weight will decrease.
Reduce excess cord lengths. Charger port cord length.
Remove Clothings. Make it barebone. ;D Simple.
Even for ESC & Receiver. But even after this you can save only a few 10s of gram, not more.
Even if you want more less weight, just try VLCC.
isnt it good enough volitation flies by itself ?
read this
http://www.rcindia.org/helis/volitation-gyro-3-5ch/
Kalyan - Great one! :rofl:
that would be vineet VC !! look up :thanks:
OOOOPSIE! Sorry Kalyan - Kudos to the young one first!
Now you know why I am yet to master RC flying - I still haven't learnt to look up! :giggle:
Holy Mackerel! How did I miss this? TRYING TO LIFT 400 GMS WITH A VOLITATION????
:bow: :bow: :bow:
@ joker
The heli you are mentioning here is i think with
3.7 v 1300 mh Battery
2 high speed brushed motor.
inbuild esc circuit
please tell me if i am correct , Because i had same type of setup some months back.
Let us be gentle... :)
Joker bhai... you seem to be attempting something that seems impossible on the face of it. Helis that can lift a 400gm payload does not seem to make sense on a single cell lipo.
Other than that, you need to figure out why you have a 400gm payload. There are cameras available now which are much lighter.
In short, it seems like you have quite a bit of homework to be done before proceeding with this project !
Try installing keychain camera.
Sent from my GT-I9100G using Tapatalk
yes swizera u r right i have the same one
the weight it needs to lift is abt 150-200 gm not 400 gm sorry for that but need help pls help me guyzzz............
@ joker
If you are thinking about reducing the weight , i dont think its a good move. The material or electronics used in that heli is all of most Important , you cant afford to remove anything out of that. Only You can remove the led which give it a fancy look, 4 led sets are there. but again very few grams u can loose. you can also remove the landing strud.( but then how will u land it ? 8-) )
lastly If you can add a 7.4 lipo with less amp (small one) it may produve enough power to carry your cam. BUT fist see if that inbuild circuit can Handle enough power from the battery , else you will BURN that.
Quote from: swizera on March 25, 2012, 10:24:33 PM
If you can add a 7.4 lipo with less amp (small one) it may produve enough power to carry your cam.
Forget this, the lion batt that comes with is mounted upfront, any change will change the cg, scrap this idea, seriously
The only way you can be somewhat successfull is by installling the 30gms key chain camera available on HK or on Ebay without any modifications to the Heli. (As mentioned earlier ). You will not be able to change the direction of the camera while flying the heli so install it at an angle which will give you the most desired results.
Hellyflyer