woohoo.... smashed my quad into the wall.... luckily board and motors are fine... can't say much about the frame though...
it flipped and then headfirst into the wall... now am building a new one... luckily nothing broke...

Yea there is a CG the controller center has to be mounted at the CG.

And you are not bugging anyone bilal bhai

Dear bilal,

Here is my pictures. ..

Shiv why dont you use a image hosting? like postimage.org

Shiv those image links are good but post them using insert image tab above like the example below


img]here[/img

Sundaram sir,

I used with img tag only. But not showing from picasa I think.

I used picasa to give a high resolution picture.

Satya will try postimage as well.

Postimage..

Picture 2

Picture 3

Thanx Shivela sir.....those pics are really helpful

Hey everyone, here is some good news,
my quad finally flew, Satya bhai you were rite, the motors were not aligned properly...... The AUW is little less than 30gms including landing gear and battery... And motor to motor distance is 100 mm.
This thing is a blast to fly, really twitchy, and a hell lot responsive than any other craft I've flown yet. There's nothing like pin-point hover, it constantly keps moving here and there, but is still is fun to fly.

Thanx everyone, specially Satya, Arun bhai and Shivela sir.... Will post pics in a while

cheers
Bilal

Bilal that is a real good news.. will be more happy if you can post a video of that..
;D

Sent from my Canvas using tapatalk 2

Great news Bilal bhai post pics, vdos if you can jaldi.... :~

atlast its flying for everyone

Hey satya bhai,
I hit a small bush yesterday while I was flying and somehow ripped the wire of one of the motors
so I tried replacing it with one of the motors of syma s107 that I had lying, and it really was a pain in the a** because the motor's shaft is of 0.7 mm dia and props have a 1mm dia hole, but neways I somehow managed to attach the two and this motor prop combo is way better than the previous one.......... Thaought I should tell others so that they may try too

btw, do you have props that can work with these motors?... With 0.7 mm hole diameter?

Regards
Bilal

Bilal bhai that was the motor that supplier sent to me at the first place (which i got replaced) so 0.7mm shaft was the reason

Its really a pain to fit the current props on the S107 motor. And these props have 1mm hole

If you are planning to buy spare motors then wait for couple of weeks, I am getting few powerfull motors which will be good with mid to large size quads ( around 250mm to 350mm)

Bilal,

Can you also share your FAT reducing secrets of your Quad?.. (< 30grms)
Some pictures if you can please...

Mine is about 34grm.

Motor+prop = 10.4grm
Lipo           = 10grm
FC             = 3grm
pencapx4    = 2.5 grm
Frame         = 8grms
               __________
                   34gms

Shiv Sir, the key here is the frame and motor mounts, instead of using the bamboo rods send bu Satya, I used 1mm thick bamboo strips  from a table mat, you can get similar strips from bamboo fans (folding ones used by women folks) etc..... And for making a platform for the FC, I used the foam plates, just stick two pieces of bamboo flat 100 mm long on top of each other and stick a square piece of foam on top for miking the platform.
Motor holders are made from caps of use and throw pens you get at 12rs a pack at stationary store... Just avoid hot glue, use ca everuwhere, and epoxy for motor mounts

Bilal,
thanks.
to the coincidence this Saturday i got the table mat of bamboo sticks from china bazaar for Rs15 for the same purpose.
will try that out.

 

Quote from: arun.sreelakam on June 11, 2013, 01:07:56 PM
Sundaram sir i dont think you can able to use that Tx..   

Arun had no luck with the hobbyking micro heli tx hence went ahead with the purchase of Fly Sky FS-T6 from Satya. I am glad I did not go ahead with the purchase of Fly Sky CT6B. Unlike a Turnigy 9X this one though 6 Channel, the features of programing are very nice and very very user friendly. it has nice features for Heli setup too with different swash setup, pitch curve and throttle curve.

A very nice 2.4 Ghz radio with cool, easy to use features.

Thank you Sundaram sir for the review. Can you please write a review on the product page as well

@Bilal bhai what exactly is CA??? can you tell its local name or any product?

Dear Satya,

It is Cyano-acetate. Available everywhere from stationary to hardware shops...

any local name?

Anabond 202
fevikwik
super glue....

and a discussion thread....

http://www.rcindia.org/tools-materials-and-building-techniques/locally-available-epoxy-andor-caglue-for-foam-planes/50/

Ahh thanks for the link Shiv