CC3D controller - need help with connections

anilntny · May 18, 2015, 06:57:26 PM

I am unable to progress with upgrade step in openpilot software ,I get error" main board took long time and connection timed out
tried different cables,lights are blinking on board

please see screen shot

anilntny · May 18, 2015, 07:13:37 PM

tried with both mac and windows pc,same error

sooraj.palakkad · May 18, 2015, 07:55:52 PM

Restart your PC, connect your CC3D, and open openpilot GCS after a while.. Usually the gcs should open up with the CC3D already detected and connected. Now enter vehicle setup wizard, from there upgrade firmware on the board.
If you don't know what you are doing, install team viewer on your PC and we can solve this out together

cyberhack · May 18, 2015, 08:00:09 PM

try doing the manual procedure

anilntny · May 18, 2015, 08:09:49 PM

Ok will try that

anilntny · May 18, 2015, 10:00:35 PM

@ Sooraj ,will do that,thanks

anilntny · May 19, 2015, 07:39:34 AM

I successfully updated the board with previous version of ground station

anilntny · May 19, 2015, 07:40:08 AM

I successfully updated the board with previous version of ground station

anwar · May 19, 2015, 04:12:30 PM

Why is the OP in the habit of creating multiple threads on the same issue ?

Merged... please avoid doing this, as it affects continuity and confuses readers.

anilntny · May 19, 2015, 09:11:42 PM

That was not intentional ,I was using my phone,its hard to get proper menus in small screen.

louis · June 11, 2015, 04:31:30 AM

1 am also facing the same problem. How do i proceed?

anilntny · June 11, 2015, 07:23:20 AM

can you explain in detail ?Is your cc3d also came with single cables ?or is it non detection of board by pc?

satyagupta · June 11, 2015, 07:45:24 AM

Quote from: louis on June 11, 2015, 04:31:30 AM
1 am also facing the same problem. How do i proceed?

The board is not getting recognized is the problem. Mr. Louise has sent the board back to me and i was able to connect and instal firmware. I am doubting that the drivers were not installed correctly causing the problem

Is there any one who can help him please? he is from Kerala.

anilntny · June 11, 2015, 08:20:25 AM

The board need to be connected to PCs only after starting the vehicle setup wizard,if one tries to start process with board already connected ,it won't work will return with an error message.

I too am using same cc3d from quadkopters, mine flies well ....

sooraj.palakkad · June 11, 2015, 08:37:46 AM

Mr louis , pm me your contact number. We can help you..

@Satya sir, please see PM.

satyagupta · June 11, 2015, 09:27:13 AM

Sooraj i have sent details to you.

desachristopher · May 16, 2017, 09:06:24 AM

Hi. I just gave some doubts. Plz help. As there r 4 ESC,s giving out 5v from the signal connector. Is it okay to connect all 4 ESC to cc3d. Or do I have to cut off the 5v out of 3 ESC,s . Plz help

Sent from my Redmi Note 4 using Tapatalk

desachristopher · May 16, 2017, 09:10:11 AM

ESC,s I use

Sent from my Redmi Note 4 using Tapatalk