how should i connect my kk version 5.5 board to a 6 channel reciever and bind it?

i need connection diagram plz

do little google search for more information..

i am searching for it since long but am unable to ! i just need clear photo of connections between flysky 6chanel reciever and kk multicopter board version 5.5... please if you can please help!!

please send me clear photos of connections between flysky2.4ghz reciever and kkmulticopter board version 5.5, which wire goes where.. i dont know
and please tell me how to bind the riciever and remote control.
i am unable to find this information on google
please sir help me...! please! 

check out the link its clearly explained

http://helihelp.rabbitsvc.com/BindingTheTransmitter.aspx

First of all you will need to bind your tx/rx. Which 6ch tx are you using exactly.
Here is a video for CT6B FlySky receiver binding


And for connections between receiver and kk board check the 2nd image posted by Ramarao,
In there the the pins on the bottom left hand side of the board(pins inside yellow box) i.e alieron,elevator,throttle and rudder are connected to the first four channels of your receiver, however sequence may vary on receiver as per your transmitter setup.
And the pins in the green box are for connecting esc signal wire for motors.

And please try to read about kk 5.5 online, there is lot of info you can find through google, like i did.
And dont hurry, take your time.You will learn a lot further in quads.

thns a lot for video regarding binding process. but i am still facing prblem with connections of reciever and kk 5.5 board.
actually there are 4 slote on kk5.5 board and 6 slots on the flysky riciever.
i have got only three wires with kk5.5 board... so m totally confused. 

connect the wires from kk board to receiver in the same order .you need 4 wires.there will be no connection for the  last two pins 5,6 (channels)

on the receiver

slot 1-alieron
slot 2-elevator
slot 3-throttle and
slot 4-rudder

i dont have four wires to connect four slots... this is what i have..

and this is the riciever...

Please look at the image, they should be able to help you figure,
you can find the manual for kk 5.5 fc @ http://www.kkmulticopter.kr/?modea=manual

are these the right connections from kk multicopter to reciever...?? am sending you a photo...!!

If you have a basic 6ch mode 2 transmitter/receiver then,on your receiver channels would correspond to
CH1 : aileron
CH2 : Elevator
CH3 : throttle
CH4 : rudder

Now accordingly match wires with your board where the pins have been marked


I have marked in white how the pins on your receiver would look like.

its ohk but are the connections right... the photo i have sent... is that right..?? 

No, it isn't exactly as shown in the pic posted in my precious replies, but yet it should work according to me, since 3 wire plug is to power the receiver, and receiver can be powered from any 1 channel.

Otherwise just exchange the plugs on the rudd and ail pins on your board to make it correct.

are there any chances that  the board will fire up if connections go wrong...

Watch the pic carefully, look at how wires have been connected, look at the colour of the wires.Board is powered by esc's, so connect the esc's properly.



Also watch the whole video,maybe twice or thrice.
You pretty much wont have more questions, if you do ,first try Google before posting here.

can you suggest size of propelor for sunnysky 980kv motor...??

10*4.5 size is ohk or 8*4.5 is ohk...??

Wt battery do u have ?
I am using 10*4.5 with these motors

You can use 8/9/10 inch props. Depends on your AUW of copter.
I use 10" on my tri now because it can handle both 3s and 2s lipo battery.Very acrobatic with 3s and kind of alright with 2s.

i use 3s lipo 3300mah 11.1 volt 35C battery
10*4.5 size is apropriate...??

which one is better tx...??

n what battery you would suggest for four 30am escs and for 980kv sunnysky motors...??