I have experienced 3 props.
So LEFT LAND props will go on M2 and M4 and RIGHT HAND spinning props will go on M! and M3.

Quote from: ved on May 08, 2013, 01:10:52 PM
So LEFT LAND props will go on M2 and M4 and RIGHT HAND spinning props will go on M! and M3.

counter clockwise rotation(ccr) on M2 and M4 and clockwise rotation(cr) on M1 and M3......just another way to say it

Haha I'm guessing you had a bad experience :p sure tell,
But with all props going same direction, I still want to see how it goes :p but scared to try on my quad :p

Actually I didn't put on props an the quad.

it will spin like crazy   do not try it buddy

Quote from: ved on May 08, 2013, 01:14:25 PM
I have experienced 3 props.
So LEFT LAND props will go on M2 and M4 and RIGHT HAND spinning props will go on M! and M3.

Correct?

correct

Hey guys
Today I tried to hover my H Quad but it was very much wobbly and was tilting towards one direction. Can any body help me?

wobbly: due to too hight or too low gain.

Titling towards on direction: try to apply opposite trim

This is what happens.
http://www.youtube.com/watch?v=1oGSKd29FiU&feature=youtu.be

Watch till 0.50

Ved the quad must be parallel to the ground then only the sensors can work properly.. use a bigger platform...
If you are using kk5.5 flash it and place it firmly..
Make sure all motors are spinning in the right direction..
Make all the trims to neutral...
Set all the gyro a to almost 45-50%
And fly it.. it will work... recheck everything....

Sent from my Canvas using tapatalk 2

Reverse yaw gyro compensation.

How to reverse yaw gyro compensation?

I dont think the yaw port is reversed... Dharmik bhai you really think so?
Its moving sideways only na? Ved did you tried trimming to opposite sides?

Yes, as ved posted in the previous page, he has kk v4.7 loaded on the board. By default it requires to reverse yaw gyro compensation. As we see in the video it tries to move sideways when initial throttle applied but if more power given it will flip or may be even worst.

Here is the link, check post no.4 at the bottom Setup Details.
http://fpvlab.com/forums/showthread.php?6331-kk-board-from-hobbyking

Quote from: Dharmik on May 09, 2013, 11:20:00 AM
Yes, as ved posted in the previous page, he has kk v4.7 loaded on the board. By default it requires to reverse yaw gyro compensation. As we see in the video it tries to move sideways when initial throttle applied but if more power given it will flip or may be even worst.

Absolutely 100% correct.

Hey Guys I did all the things told here but I am facing the same problem. Can it be due to wrong props on motors?

Hi Ved
Please have a look at this post.
http://www.rcgroups.com/forums/showpost.php?p=18609175&postcount=73
Prop direction is given there. Please make sure that only yaw gyro is reversed. As i remember lazyzero flash tool has feature to check and reverse gyro on the pc during flash. The procedure is bit complicated but once you fix that it will fly great. May be you might have to reverse more than one gyro direction but mine worked fine for yaw gyro only. Please note that gyro pot direction and gyro direction are different.

OK. I will see.

I think there is some problem with the firmware. When I move the aileron stick to right M1 and M4 should speed up but it doesn't happen. M3 speeds up. Same case with all other controls. What may be the problem?

HELP

Reset the board to default settings and load the motor layout again. Then without any PID setting, test the motors without prop. If the throttle is acting weird again, Change the ESC. Go in for Turnigy Plush ESCs. Those are the best ESCs with best resolution.
This will definitely solve your problem.

OK

Hey Guys I think I found the solution. Every time I used to flash my board I flashed Quad rotor instead of X rotor. I will re-flash it again and try.