Help on quad copter

jeet8066 · April 30, 2015, 09:57:04 AM

Hi all i have purchases Reptile 500 ARF Kit. I am getting problem in fly quad copter. every this connected properly & all controls are working fine but issue with flying. after given full throttle quad not flying. it's stay on ground only. Please suggest me.
Technical details & image given below:-

1.XY500 Reptile frame x 1.
2.Avionic Hexa Quad controller.
3.SunnySky 2212 980KV motors x 4.
4.SimonK 30A ESC x 4.
5.1045 Propeller x 2 pairs.
6.Batter 2600mah 11.1v, 35C.

Darshan for multirotors · April 30, 2015, 10:49:48 AM

Is there any jitter in the motors while spinning??

jeet8066 · April 30, 2015, 10:52:21 AM

No

jeet8066 · April 30, 2015, 10:54:14 AM

if u hv more experience on quad then can u come online on chat? plz

jeet8066 · April 30, 2015, 10:55:48 AM

if u hv more experience on quad then can u come online on chat? plz

Darshan for multirotors · April 30, 2015, 11:02:16 AM

You can contact the rcbazaar.com to solve your problems.. I am not quite experienced with avionic hexa quad fc

jeet8066 · April 30, 2015, 11:05:52 AM

according to you what is prblm? esc or motor issue or anything else?

Darshan for multirotors · April 30, 2015, 11:23:08 AM

Can you post a video on what is happening

jeet8066 · April 30, 2015, 11:24:36 AM

give me ur mail id i will share with u.

Darshan for multirotors · April 30, 2015, 11:27:30 AM

Check pm

jeet8066 · April 30, 2015, 11:29:44 AM

video size is 45Mb not possible on whatsapp. it's already uploaded on my drive. give me ur mail id i will share with u.

Darshan for multirotors · April 30, 2015, 11:32:24 AM

Okay

globalmilind · April 30, 2015, 11:33:21 AM

Check if motors are spinning in right direction.
Props seems OKAY!

jeet8066 · April 30, 2015, 11:35:05 AM

check ur mail i hv share with u.

jeet8066 · April 30, 2015, 11:37:36 AM

yes all r connected right direction.

Darshan for multirotors · April 30, 2015, 11:38:55 AM

Check again... check if the motors are spinning in the correct direction and if the right prop is on the right motor. .. I think this has to be the reason why it is not lifting off

IndianHobbyShop · April 30, 2015, 11:44:17 AM

What Voltage are you getting from that battery at fully charged state?

jeet8066 · April 30, 2015, 11:45:20 AM

11V

meet2ami · April 30, 2015, 11:50:20 AM

Are you using a 3S lipo? If so the full charge voltage for 3S lipo is 12.6V. 11V is too less!!

Darshan for multirotors · April 30, 2015, 11:52:16 AM

I suppose 11.1v is 3s

jeet8066 · April 30, 2015, 11:56:37 AM

Batter 2600mah 11.1v, 35C.

Darshan for multirotors · April 30, 2015, 11:58:44 AM

Run the props (be careful)just put tour hand under and above the running prop.. if the amount of air is more on the upper side.. The prop is wrong

jeet8066 · April 30, 2015, 11:58:53 AM

9632788810

parichya.gautam · April 30, 2015, 12:14:29 PM

If its the KK2 , then yes i may be able to help you

Just contact anywhere you want

K K Iyer · April 30, 2015, 12:23:25 PM

@jeet8066,
Another member had a similar problem recently.
On looking at his video carefully, i found that the airflow was upwards!
The props were pushing the quad into the ground!
Normally it should show a tendency to lift near half throttle.
No way you can use full throttle without hitting the roof!

Your prop position appears correct.
Check that front left motor runs clockwise when seen from above. I suspect it goes anticlockwise!