Hello,
I am keep getting the CFG-ERR error at the bottom of the screen. When I click "Start" for calibration the sliders doesn't respond except Aileron Throttle . Cant calibrate elevator and rudder?even though when i reverse it from naza assistant and 9xr still it doesn't work?Only throttle and Aileron moves/works?now only throttle moves?
any idea why its not working?

connect aileron/CH5/CH6(any working channel) from receiver to evator then rudder and check naza is faulty or not.

From your video the first thing I notice is your mode 2 radio is configured in RETA configuration but in you mixer menu,channels are not following the same order infact its configured as TAER . Yet your Thr and Ail stick are matched correctly to Naza, so you have connected those two channels correctly to Naza irrespective of configuration.

If your Naza is fully functional and if you have checked and connected Naza to RX correctly polarity wise(cant see it in video), then you can try change the channel assignments in Tx Mixer menu to

CH1- Ail
CH2- Ele
CH3- Thr
CH4- Rud

If you do that^^ then ideally connections from your Rx to Naza should be like:

CH1 - A
CH2 - E
CH3 - T
CH4 - R

Their is chance it may work.Similarly, people who faced similar error(no non working channels tho) got their issue solved by uninstalling Naza Assistant, cleaning up folders, and reinstalling.

Quote from: akhilzid on February 01, 2015, 10:25:37 AM
connect aileron/CH5/CH6(any working channel) from receiver to evator then rudder and check naza is faulty or not.

Hi
i did connect on other channels like CH5 CH6 but no luck still i am having same problem and other ppl also having similar issues like me so i don't think my naza is faulty.
http://fpvlab.com/forums/archive/index.php/t-10620.html?s=ab152e4c66f7dc1c8137a0cea877d6ab

Hi
i did set up according to your channel set up which are CH1 - A CH2 - E CH3 - T CH4 - R CH5-U but still no luck even though i uninstalled naza assistant and reinstalled again but i still have same issue only throttle works .I double checked the polarity its fine.I dont know what to do on this stage really frustrated .please see my video link

just to clearify about RETA configuration? is my tx settings are ok??
I appreciate your help.
looking forward to hear from you.

Hi SideWinder
i did set up according to your channel set up which are CH1 - A CH2 - E CH3 - T CH4 - R CH5-U but still no luck even though i uninstalled naza assistant and reinstalled again but i still have same issue only throttle works .I double checked the polarity its fine.I dont know what to do on this stage really frustrated .please see my video link

just to clearify about RETA configuration? is my tx settings are ok??
I appreciate your help.
looking forward to hear from you.



[/quote]

Hi SideWinder
i did set up according to your channel set up which are CH1 - A CH2 - E CH3 - T CH4 - R CH5-U but still no luck even though i uninstalled naza assistant and reinstalled again but i still have same issue only throttle works .I double checked the polarity its fine.I dont know what to do on this stage really frustrated .please see my video link

just to clearify about RETA configuration? is my tx settings are ok??
I appreciate your help.
looking forward to hear from you.

just reset your naza lite to default settings... calibrate your stick in radio settings... than setup your radio like guy did in video





and than setup naza lite in assistant software again and calibrate tx... hope this info would be helpful for you
(i also use 9xr with my naza)
(editing also setup new naza profile again in your radio..)   

regards

Thanks for your Info
I will give you an update once i finish everything.
Regards

sorry bother you again what is Basi Calibration on Tools section when i go to naza assistant 1.0 on tools i noticed there are some calibration options .Can i calibrate from there too?

Basic calibration is not related to radio, is for sensors(accelerometer and gyroscope etc.)

Look at these http://fpvlab.com/forums/showthread.php?24316-Naza-M-V2-Error-29
http://youtube.com/watch?v=HEFL04piZIM

Thanks Akhilzid let me check

reset your naza to default settings...

regards

I did but no luck:-( let me try again i will upload a video for u you see what i have done :-(

and also which module you are using....? and set the receiver type to traditional not D-bus or ppm
(set it to traditional and problem solved)

regards

software : Naza Assistant M lite 1.0 version
Module: frsky d8rII-plus
i did set the receiver type as traditional but only throttle channel works

attach only four servo leads to receiver
A. to CH1
E. to CH2
T. to CH3
R. to CH4

( connect  F1 and F2 ports with servo lead attach battery and then attach naza to computer ( it is in safe mode now ) open naza assistance software there shows update available to 1.00 version update it setup it. surely it will work..)

keep one thing in mind your pc must have internet connection

regards

sure but im bit confused F1 and F2 ports with servo lead attach battery ? did u mean led v-sen servo extension? please explain to me :-(

if possible could you show me a video
many thanks

connect f1 and f2 port with servo extension cable.. ( f1 and f2 port on output side ). and than power up naza and connect to pc.