Hey friends, after last outdoor crash i have rebuilt my quad again. It flew really well, more than two minutes in perfect hover position, however at last due to lack of skills i crashed it from above 10 feet. Luckily everything survived except frame and motor shafts and cap of roll gyro came off. I am really satisfied with hk board performance so i went ahead and put everything together.

What material are you using for the base, where you mount the HK board...

satya bro l am using plastic tray material for center plates and 12mm aluminium channel. frame is completely handmade.

Bro any suggestion where would i something like that???

If you see the latest post by me here, http://www.rcindia.org/multirotors/help-with-my-quad/ i used a 2 mm plys which gave up after a hard landing.

Was thinking to use something very light and stiff, any suggestions??

BTW i got a good flight yesterday was able to lift my quad more than 20-25 feet in air will post video soon.

Neighbours are on vacation, streets are empty and i got it on video.

super stuff Dharmik.

Bro i have got into a problem with my quad if you rem at the very start my quad used to do round and round on the yaw axis. After sometime getting some inputs from you and other members of RCI i got it fixed. Now i have replaced the base with a 2mm CF plates and it has started the behaviour again. The only thing is different that its more violent now.. It rotates as if its on mission to kill someone

Any inputs, sorry i cant took any video because it was very dangerously flying so i had to stop in less than a minute or two.

@satyagupta

Yes i got your point that rotating roundly.

it happens when CW and CCW (Clock wise and Anti Clockwise) aren't correctly placed. just be aware of the Front, Rear, Right, Left.
here is an example for that---X config.(works perfectly)

                                        Left

                          CCW     X        X   CW

                      Rear              +        Front

                          CW       X        X   CCW

                                        Right


***This is a method done by using IMU 6DOF.(Front,rear,right,left)
It depends on how you actually placed your Gyro Sensor.
Above you can see Gyro Front-Rear-Right-Left.
According to your Gyro Position you need to place your propellors CW and CCW.


For Guidance;
Mr. Ronie,
+918977518086

Satya bro i don't know which fw you have flashed but i had to reverse my yaw gyro on kk 4.7 fw but as you said it started again then probably something wrong with new setup. It also happens when arm is slightly twisted by mistake so make sure motors are mounted at 90 degree angle. Btw i will have to remove background music(content id match) p

QuadRotor - Street Hover
Got really nice maiden flight by hk v1 board and kk4.7 firmware

Specifications:
Motors: 4x http://www.hobbyking.com/hobbyking/store/__5429__AX_2308N_1100kv_brushless_Micro_Motor.html
ESC: 4x http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=15202
Battery:
(1) http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9942
(2) http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=8934
Props: 10x4.5 CW CCW
Frame: M2M 530mm aluminium U type 12mm
Radio: FS-CT6B
FC: HK V1 ATMEGA48PA 4kb FLASH
Firmware: KK 4.7 plus config
THROTTLE: 120 EPA

Here is one more video
http://www.youtube.com/watch?v=8EAT5wlfCuk&list=UUWUt1UoPQ_X4jAmr3Qh6SLw&index=1&feature=plcp

Dharmik bro no landing gears or stands for landing?? btw the way you are controlling quad you dont require one buddy but still is it ok to fly a quad sans landing gears???

No it has landing skid of hiller helicopter bought from raja mastana, please check pic i have uploaded above few posts.

Hmmm i would need one too, any LHS or any store where i can look out for it?

@satyagupta: That was just the question I had asked Dharmik bro in a PM...

Here it is satya bro. Only 30rs p
www.rcbazaar.com/products/773-landing-skid-hiller-450v3.aspx
If you find bigger skid please do let me know.

Hello Friends

Here is one affordable and simple solution for your quad flying problems. This product, NAZA, is manufactured by DJI Innovations and very simple to use. After hard work of days, you can simply avoid crashing it. Please check the video below.



You might like to visit our web store for more details.

Good luck to you all and happy hovering.

Regards,

Sphere Hobbies

It seems to me that DJI NAZA Flight controller is currently the HOTTEST FC on rcgroups.

http://www.rcgroups.com/forums/showthread.php?t=1652849
http://www.rcgroups.com/forums/showthread.php?t=1659354
http://www.rcgroups.com/forums/showthread.php?t=1536553
http://www.rcgroups.com/forums/showthread.php?t=1606280
http://www.rcgroups.com/forums/showthread.php?t=1582036
http://www.rcgroups.com/forums/showthread.php?t=1659767

Yeah naza, wkm are popular and multiwii, rabbit fcs next to them..

new harness is allmost ready

ummmm this is the way i am doing thought this is the most common way..

What happend satya bro? My previous harness was bit long. All i learned is make ESS to BATTERY connection as much short as you can. You can extend esc to motor connection if required. Yeah heat shrinking left. I have added wires for lights too.

Nothing bro, i thought this is the way everyone is does it.. Anyways good stuff you using silicon wires or normal ones?

Ya silicon wires bought from rchobbyaddict.

w00t man, i kept looking for in ebay and other stores... any link for us bro pleaj...