yes it does, i observed too, some software fix is neccessary, also there is moderate (manageable) jitter in channel 4 in my radio

PS
Yes! i have done everything changed four servos, changed channel assigment etc, lastly reassigned channel and it is OK (Eliminated jitter channel)

Received the rcb7x today. The rx seems unbound. Anyone, how to bind? The CD manual I got has got problems reading so can't read the manual. Kinda stuck, review is far off

Servo jitter in a new tx is usually because of poor quality/poorly fitted pots.

Solution : open up clean pots with spirit and reassemble

@girishsarwal rcb7x manual has the instruction to do so. Check the rx for two tiny buttons over it. One is for trainer function and the other is for bind. Just press that bind button with tx on..

Quotercb7x manual has the instruction to do so.

Thanks Avesh, but like I mentioned, my problem was I could not access the manual on the CD, the recording layer seemed defective. wouldn't have posted such a dumb question otherwise. I now have the manual downloaded (location provided by RCBazaar guys) and your instructions.

But yes, something that goes without saying for RCBazaar, their support is great and really follow up on stuff. Look forward to bind it, have fun and share my experience. Many thanks gentlemen.

GS

i have the set up for plane and when i connect my esc to moter it makes constant beeping but my servos and all work's properly and the battery was fully charged 

Friends - could anyone send me the RCB7X manual ??
I have the manual CD but my CD drive doesnot read it.... but the simulator CD works...

Hi,

i will upload and send u the link.
its about 52mb. 

@coco you need to setup throttle end points. For your purpose just check on youtube "set throttle point dx7".

Quote from: santhosh-r on May 30, 2013, 09:58:49 PM
Friends - could anyone send me the RCB7X manual ??
I have the manual CD but my CD drive doesnot read it.... but the simulator CD works...

Hi,

https://dl.dropboxusercontent.com/u/29915798/RCBHARATH/Avionic%20RCB7X%20Instruction%20Manual.pdf

this is the link for the Manual:-)

Friends .... I see " 12.5mS Frame Rate" on my RCb7X screen ...is it possible to change the frame rate to 20mS i.e. 50Hz.... .
If yes ,,,then how should I do it?

Is there any other simulator software compatible with this wireless simulator like Phoenix ??

Quote from: santhosh-r on June 01, 2013, 06:37:29 PM
Is there any other simulator software compatible with this wireless simulator like Phoenix ??

for me its working with phoenix4 and RF G4.

Give me more details connecting to Phoenix 4....I too have it , but when I enter it , it shows that there is no USB simulator connected..

do u have genuine or a pirated version?

A pirated one that came with the 12 in 1 sim from RCdhamaka..

@dinesh phoenix4 how??? . RCB manual never mentioned about phoenix4 .

avesh i am using phoenix 4 with rcb 7x and its working.
i just downloaded pirated phoenix 3 and updated it.


i am receiving all the updates and it dosent need much graphics its working good.

Guys can anyone use phoenix in win 7
Mine is not working.. what may be the problem... simply closes when I open it...

Sent from my Canvas using tapatalk 2

Quote from: arun.sreelakam on June 02, 2013, 09:47:17 AM
Guys can anyone use phoenix in win 7
Mine is not working.. what may be the problem... simply closes when I open it...

Sent from my Canvas using tapatalk 2

the phoenix sim comes in 12in 1 pack dosent work,
just download it from torrent :-)

Thanks for the info dhinesh... I will download it...

Sent from my Canvas using tapatalk 2

Quote from: arun.sreelakam on June 02, 2013, 10:40:17 AM
Thanks for the info dhinesh... I will download it...

Sent from my Canvas using tapatalk 2

:-)

Hello friends I am planning to order this rcb7ch TXRX , I have read few threads and comments where ppl are selling it as they got a better one and this txrx they had issues like lost control and flight crashed etc. can some tell me whether I can go ahead with this or a better one or fly sky or trunigy is better

Can anybody (preferrably a direct end user) post a long term usage review of the RCB7x and the RCB6i to help potential buyers ?
What according to the sellers and service providers are the teething and recurrent problems of both these sets after about a year of launch and what are the reasons of control loss and other problems which have been reportedly experienced by some users?

best regards,
Dr. A Ghosh

i want to know is there any receiver can be connected to avionic rcb7x

every biginner use to fix these in their first plane and what if it crach out in my case it blow up before reaching to the airplane


i have every item to fix on airplane except the receiver , i suggest rc bazaar should have good supply of
receiver because it is unique item with work only with avioninc 7x if there was any match then i can continue my project rest

every sunday i have only thing to do is to watch update on rcbazaar website this is bad there should be any alternate so that we can continue with our project.




I am in need of some assistance to connect rc electrical
Equipment I was working on my next project with equipment from rc bazaar
Project cost me rs 10000 I got everything but was fail to connect them
Properly and esc and receiver blow up
Here is the detail

      As it is given on the website of rc bazaar on avionic 7 channel transmitter setup, I connected esc with the battery And then to the 3 rd channel of the receiver then I start the master Button of the receiver and after that I switch on the transmitter but, I smell that something is burning their so I stop connecting servo to check for connectivity,

I Remove all the connection and put my hand on esc it was heated and when I see the back side of the receiver I see the spot where it burnout and some smoke collected in the box as you can see in the picture
 
Now
             I have nothing to say maybe it could be my luck or something went wrong. I got everything battery
Motor, transmitter, and esc I also build airplane for my setup only thing
Remaining is receiver so I spend about on these items I want it to work
My project is completely stopped as new set of receiver will com e within 2 weeks

I waited for 3 weeks then I call rc bazaar to respond me about the receiver, but I got negative feed back I do not know the exact time period of getting new receiver

As it is china made anyone in the form can help me is it tx is compatible with any 2.4 ghz receiver so that I can continue my project, Reset I can not rely on rc bazaar they hands off from the receiver, is fly sky receiver is compatible with avionic tx
..


I do not understand how a 5 amp of current can blow up the receiver at the first time.
The simulator provided with the pack is also not working. I even do not have any documents with this package how to setup with the receiver, no details at all.



If we are in a hobby then parts will broke out and it is supplier's duty to have all parts supply so that we can replace it and continue our project, if receiver is unique and airplane crash landed then what to do everything is of no use

In that case we have to buy a new set of transmitter and receiver, that is not correct and what if we open the pack and rc equipment blow up before we install it in our plane
What we can say about the product.


wingmanbunty