Okay so I'm using a fs-th9x and I m not able to simulate it with smartpropoplus and FM's.
I am using a general purpose 3.5mm aux cable. The smartpropoplus says the signal is weak. Also my tx has antenna attatched to the RF module. so is that the problem ?
I plugged in the battery in tx and connected but then the software can't connect.
Help me with this.
:banghead: >: :(
First the tx should be in off position when connected, the rf module connected is not the issue here, also make sure the line in or mic volume is full, if that does not work use the boost setting under mic settings & also the sound quality should be set to 16 bit (high quality) under mic properties.
@Amit:
I did that, I plugged in the battery, removed the module, as I read that it might be dangerous for the module if plugged in while being connected to the PC. Then while the Tx was off, i plugged it into the PC, mic n line in were at their max, doing all this, still i got with no response!
Do need to plug the module in, so that the signal becomes strong, or the tx starts sending the signal ?
Try connecting line in port behind CPU other than front panel.
You are connecting TX directly to PC?? no simulator dongle in between?
I have a unused,unboxed dongle. If you need one, let me know.
if you are using a USB sound card you may have issues like it detecting and after a 1sec or so randomly starts showing transmitter disconnected and 20ch etc.
Try adding resistor divide network to keep the audio port from overloading and also its good to use mono jack.
Exactly what happens in my case !
After 1 sec the Smartpropoplus shows "disconnected" !
How can I add resistor dividor n/w to PC ?
o.O
see this link
http://www.smartpropoplus.com/dnn/Hardware/Spektrum/tabid/94/Default.aspx (http://www.smartpropoplus.com/dnn/Hardware/Spektrum/tabid/94/Default.aspx)
I have used a mono cable, 3.5 mm male to male cable, nothings works except fluctuations ....
so are you using a usb sound card ? which OS win 7 32 bit or ?
dont plug it in the mic in port. i did that and it didn't work on mine... i would plug mine into the third port (the black one) next to the audio out/in ports....i dunno what it's called though.... but even then there is slight noise in the signals... the sticks will keep twitching even when you aren't giving any input... better is to just buy a simulator dongle....
@ankit: You're right !
Works perfectly now, it had to plugged into the 3rd port other than audio & mic. !
only problem is that, heli's not working well. but plane'll do for now !
Thanks everybody who tried to help me !
Thanks very much !
That port is what we called "Line In" Is posted in reply #4.
Quote from: akhilzid on February 12, 2015, 12:26:15 AM
That port is what we called "Line In" Is posted in reply #4.
8-) ;D :giggle:
Quote from: theObnoxious on February 11, 2015, 09:03:44 PM
only problem is that, heli's not working well. but plane'll do for now !
for a heli you'll need to make a different model with the throttle on a pot and the collective on the throttle stick...
@Akhil: thanks for the info. bro, I was to worried I couldn't fig. out. Now I do. Thanks ya'll.
:)
;) ;)
:banghead:
I have my new th9x from flysky.. I installed Phoenix rc and I tried connecting it with my tx using a stereo cable on the tx side and a sim dongle in the usb jack .. but it shows nothing but this !
' your transmitter has Been disconnected '
:banghead: :banghead: :banghead:
Pls help
You need to buy a simulator for that.. many paid simulator softwares will work only with its own simulator dongle.. or you can buy an all in one simulator from any lhs
Where did u bought this sim from? For many sims, there are multiple sim sofwares in the dvd upto 8, but the dongle will work with only one of them.