Flysky receiver led not blinking

Started by giri111820, March 07, 2014, 06:28:39 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

giri111820

When i tried to bind the transmitter and receiver of flysky trans and rxr led was not blinking in the rxr part. can anyone tell what is the fault is the rxr not working or something like that.

v2 eagle

what is the TX model you are using, those flysky manuals are rubbish and they may not be exact. I once had the same problem and got it solved with an expert from Chennai.
If everything else fails, go to sholavaram any sunday and take the help of gentleman named Rajashekar. he drives a white i20 and he has good knowledge about these radios.

Ashok.P
FPV with head goggles

http://ashokpkumar.wix.com/mysite

arun.sreelakam

Giri cal me once you are free... I will explain the things.. :)
Hope you know my number..
Turnigy i10|Flysky 9xb|Hoverfly quadcopter|Arduflyer apm 2.5 with gps|Pixhawk|Homemade micro night vapour|Homemade ornithopter(in progress)| Reptile Quad with Gopro Brushless gimbal | Naza v2| APM 2.6 with GPS | Micro quad self made | FrSky| v911 Helis | 1200mm Hexacopter with 5d gimbal | 1300mm x8 With Red Gimbal | 1000mm Octo|

giri111820

sure bro i will call you there was a problem with my receiver it was not working thats y put up this post. now i changed it from the buyer its ok now.

abhishekfast

i am not getting any LED on RX tried with 2 lipo's

Can anyone help me to check what is wrong. i have connected rx through 20 AM ESC.

SideWinder

#5
Have you binded the Rx with Tx? Was your Tx switched On when you tried to power Rx?

If the Rx is binded, Led comes on when Tx is switched on. If Tx is off, then Led on RX wont light up.

abhishekfast

Rx was binded when used lasttime. i tried with TX on/off, rx light not glowing. TX is beeping dont know why....

SideWinder

In hindsight should have asked you which Tx/rx are you talking about because I gave you details regarding 9Ch Flysky Tx/Rx.

The 9ch radio beeps if the switches are not in required position giving you "Switch Error" on screen or continuous beeps due to low battery voltage if you have set it in the Tx. Try changing or recharging the battery other than that never had my Tx beeping.

Also check whether you have properly inserted the BEC wire from ESC to RX, polarity wise. If connections are correct and, Rx is binded and battery voltage is adequate, then Rx LED should light up if Tx is ON.

abhishekfast

connection is correct from esc , tx is beeping due to low tx battery. is low tx battery cause of rx light not glowing. i have flysky t6

SideWinder

Can be due to low battery.
Can be due to no binding.
Can also be due to broken antenna on tx/rx.
Can also be due to damaged Rx or Tx.

So first try changing batteries, perform binding, then check whether the antenna's are alright. Try to use a different Rx or Tx. You got to eliminate the issues one by one to find the exact error.

utkarshg13

Gone through the whole thread. Seems like people are having a hard time in binding. Guys, there are certain things that are to be followed in a particular manner. Unless, you won't do that properly you are going to make mistakes. Please go through the under mentioned steps and tell if the problem continues...
First of all, whenever posting about radio's please do post which brand/model you are using. It becomes easier for people to help you. Since, almost everyone here has got almost every brand radio.
Now, ensure that your Tx, Rx antenna is fine. In case it is a flysky receiver, the antenna needs to be taken care off. Next, check whether Tx batteries are charged or not. Whichever battery pack you are using it should be properly charged before use. I've got Fly FS TH9X and FS T6 as well. So, the binding procedure remains same in both.
1.) Put charged batteries in your battery case.
2.) In case it is a FS TH9x, 9 channel flysky radio put the module behind the radio(if not done before.) In FS T6 it is already fixed.
3.) Take your receiver and put the bing plug you'd got from in the set. It is usually written as to where you need to plug in the bing plug as, BIND
4.) Connect the ESC to the Rx. Ensure that you do it in right direction. The pins in Flysky receivers are as Signal, VCC, Ground. You need to make sure that the colour combination comes as white(signal), red(VCC), black(ground) or yellow, red, brown where white/yellow comes first.
5.) After the bind plug and ESC are plugged in Rx connect the battery to ESC. As soon as you connect battery, you'll notice the red LED blinking.
6.) Now press the bind switch on your Tx, keep it pressed and switch on the Tx.
7.) As soon as the Tx is switched ON the LED would stop blinking and glow continuously.
8.) Disconnect the battery, remove the bind plug, and switch your Tx off.
9.) Connect servos, check your connections and then switch your Tx on and then connect battery to ESC.
:hatsoff:



"If you were born with wings, do every thing you could, for flying."

utkarshg13

An important point to be mentioned, in case it is 9 channel flysky or any radio which has a detachable module behind for Tx antenna, never switch it ON without the module. Ensure that every time you switch it on the module is plugged in.
"If you were born with wings, do every thing you could, for flying."

abhishekfast

i found the issue, cable coming from ESC to RX is having issue. i saw LED blink once when i lift the setup. then my tube light blinked :) its not problem with RX its issue with ESC. When i am moving cable coming from ESC LED on RX is blinking. i have hardly used it, only 2-3 times to check servo setup. Its AVIONIC 20 A ESC

utkarshg13

There must be a broken/loose connection in. Or might be your receiver's pins are broken/faulty. Try with another ESC.
"If you were born with wings, do every thing you could, for flying."

abhishekfast

i dont have spare ESC but i am sure its ESC. lets see if i get replacement for it. Its only 2 months old. If not i will open it and check.

utkarshg13

If you are not having any spare ESC then just try to get it replaced. Might be during handling/using wire must have got somehow pulled out.
"If you were born with wings, do every thing you could, for flying."

gbisht

I come to this thread and see many experience people guiding for Rx issue, I am also facing strange issue,
if its possible, please spare some time and guide me as well, I hope you guys are still active on forum

http://www.rcindia.org/cars/hobbywing-quicrun-1060-brushed-esc-issue/msg309594/#msg309594
HSP 1/10 Nitro Tyrannosaurus Off-Road Truck
Thunder Tiger 1/10 SSK V2 Nitro Truck with Radio
HK-300 3 Channel 2.4ghz FHSS Ground Radio
Turnigy 9x 8-Channel
HK-250GT