i just wanted to know if i can connect my flysky th9x to pc via 3.5mm audio jack male to male cable? i have downloaded phoenix simulator, also smartpropoplus and ppjoy. i havnt plugged it in, just wanted to confirm is it okay? or do i need those audio jack to usb cables?
Hey You need this to connect.... Its an interface between your Radio and Computer...
PM Sent.
Remove the module and connect :thumbsup:
yeah aditya, i searched onlne, you can connect without the usb thing. i got the software. some transmitters which dont have removable module n antenna have to be modded adding a resistor inside or something. but myn is removable with antenna. so can i join it with just the audio cable? can there be any harm in it?
Thats great..! Please share the link for the same because, I myself this thing and hasn't worked due to some software problem... Trying since few days to repair the issue... but so far can't get any solution...
You are using FLYSKY TH9X right?
Thanks what i have and i can remove the module out of it. Just remove the module, connect the 3.5mm audio jack male to male cable (you would need a USB dongle for it as mentioned by adiboy) start the sim. If every thing is good then sim will detect your TX.
Some dongles have switches, you have to set it to correct simulator for it to work.
okay i'll just try it with just audio jack. and yeah i tried to upload files of it but after finishing uploading i get this.
Forbidden
You don't have permission to access /radios-and-receivers/ on this server.
ok, so i have been trying to connect my FS Th9x(same thing as turnigy) but for some reason, whenever i run the sim, the controls go nuts! windows also cant calibrate the controller....!
i installed PpJoy and propoplus.... and now i am confused...
on top of that, installing drivers is a pain, because i am running windows 8 and it's beautiful(thanks MS) Signed driver control rubbish....
please help!!!
thanks!
aniket
@Aniket- call up RcBazaar and they will guide you through the whole setup process and clear any problems if any(considering that the sim was bought from RcBazaar)
the sim is FMS.... it's free.... about the controller, i guess i will.... thanks prateek! btw... how do you use yours with a sim???
thanks
aniket
I have flysky th9x tx modded with er9x firmware
http://www.hobbyking.com/hobbyking/forum/forum_posts.asp?TID=1428
According to above link i should connect male to male audio jack in my tx's trainer port and to line in jack of my pc and tx should turn on
I did that but my tx didnt turn on .
Wht is this is so ???
Did you removed your Module ?
yea harsh! first off, how did you flash er9x?
secondly, try to remove your module ..
Aniket i ordered a usb asp programmer,downloaded hex code and other software from google and schematic diagram for soldering wires to atmega processor and flashed it
Here is the link http://code.google.com/p/er9x/
And yes i removed my module and connected audio jack but still tx is not turning on itself neither by pushing power button of tx
i have a turnigy 9x 9ch...And i bought a sim (12 in 1) from RCD a few weeks ago.
i have installed Phoenix software .
i tired to connect ...but the TX was not gettin detected..... :banghead: :banghead: :banghead:
tried almost several times....
do i remove the module on turnigy 9x ???
guys plz help...
Yes buddy you gotta remove the module . Gently remove the module (there might be a wire inside, don't damage it ). Module is connected by 4pins from inside so gently pull the module . (Module will be hanging) PLEASE correct if wrong
And as soon as you connect the 3.5mm cable the tx will switch On. And You are ready to go .
I have used the FLYSKY 9x with Rcbazaar Sim and it works flawlessly . Will work with Turnigy too . But as the Module is hardwired to antenna , you might wanna have a look on the mods.
www.hobbyking.com/hobbyking/forum/forum_posts.asp?TID=15911
And that's the reason FLYSKY is better than Turnigy hehe
what battery are you using?
Sent from a potato using a lamp
I thought my trainer port is faulty so i checked it by putting battery in tx and conecting audio cable in its trainer port and then measuring votage across other end.
It is giving nice 5 volts voltage and i think that should be enough to switch on tx but i am still not able to detect the problem
Hi All,
Today I connected 3.5mm audio jack male to male cable from my FS-TH9X to PC.
I Downloaded installed the Smartproplus and ppjoy and did Ca-liberation.
I used with BMI-Flight Simulator. Worked fine. Controls are responsive.... ;D
http://rcdeskpilot.com/bmi
aniket you're lucky... it was a pain in the butt to calibrate it with Phoenix rc.... and I can't install smartpropoplus on Windows 8 easily because windows doesn't allow unsigned drivers to be installed. it's a pain....
Sent from a potato using a lamp
windows 8.1 is even worse. forget to upgrade to windows 8.1 if you are in windows 8 I DID AND SUFFERING NOW
@nitesh....you need to trust me on this one....
i have been working for Microsoft support for past 10 years+
n with my experience ..i have found..
all new wIdow$ os are little unstable. :banghead: :banghead:
micrO$oft has a history of make unstable OS...(initially).....thn they stabalize it with patches and service packs... :giggle: :giggle:
thanks druva...will try this
I use windows 8, works without any problem. Phoenix rc also works without any problems.
Download again and try a reinstall if you are having problems. I was using th9x before, now using the HK orange. Although had to modify the cable a bit for the transmitter to work for simulator. Let me know if anyone who has orange transmitter and has problems with the simulator, I can help fix,
Sent from my GT-P3100 using Tapatalk 4
woah there nitesh.... windows 8.1 is awesome... have you tried the beta version? or are you just talking through your hat? if you hate windows 8 so much, downgrade! nobodies forcing you to use it...
Sent from a potato using a lamp
I am using the preview version of windows 8.1 its just so dummy damn slow made my computer a lot slower and I don't find any speciality in that the main problem I can't revert back to windows 8 which is just a major issue
btw please leave this and come to the main topic
nitesh it's a preview version! a beta version! not the final one... the preview edition has bugs because Microsoft is still working on it! and anyways, Phoenix and my TX work fine with Windows 8.
what you need to do to install smartproplus, is disable the "digitally signed driver enforcement" setting. this prevents unauthorized drivers like ppjoy and smartproplus from being installed, and is enabled by default.
Sent from a potato using a lamp
thanks
i want to use flysky th9x with phoenixrc simulator to fly helicopter
it is working fine with simulator but
i am unable to set negative pitch curve in helicopter
when i go to idel up mode centre position is nutral pitch and both up and down pitch are positive
so in both directions i end up flying upright can not do a inverted flight help me... :help:
any one who is able to fly helicopter in inverted position???
Hello .. Pls give me the brand name of that .. I need it ..
Hello friends I used following cable WITH FMS and it works.
see attached image.