Hi Guys,

Just registered to RCIndia and dropping my 1st question about TX and Simulator cable.

Doubt 1.
I have purchased
http://aeroworks.co.in/radio_8505.html

Will this transmitter work with following FMS Cable
http://rc4all.co.in/product_info.php?cPath=35_86&products_id=146

I went through posts who have mentioned same but none has confirmed this as working.

Doubt 2.
Also if anybody has used this combination, do I need to put battery in tx while using it as simulator?

Doubt 3.
should I go for FMS or http://rc4all.co.in/product_info.php?cPath=35_119&products_id=145

Thanks In advance
-Abhishek

you can use normal programming USB cable for that transmitter as a simulator cable, i am using it for aerofly pro deluxe and fms. however you need to install a few drivers and some software.

@ coderbanna :
Hey thanks for reply,

I tried using PPJoy and T6-sim....but in T6-sim it is not detecting any port.
and my t6config is woking fine.

I hope by drivers/software you referring to these two, if not please let me know which drivers/sw.

did you tried selecting port COM-3 in t6-sim it works perfectly.

My com list shows blank...

did you connected your transmitter and  powered it on?

remember i am talking about normal programming USB Cable like this one

http://hobbysea.com/products.php?69&cPath=8&sid=ce9b609426ac4e39d907f83b2190cb50

Yes I have the same one which came with TX,
I use the same one for t6config...

if you can see it in t6config then just install PPJoy, make a virtual joystick by default settings and then use this joystick in T6Sim. its quite easy to do. use port Com3 when asked.

Hmmm.... i tried it but for some reason my com port list is empty in t6sim....
I will try it once more and will post images here.....may be it'll help....

Also which os ur using....m on windows 7 ultimate....

same here, windows 7 ultimate

it doesn't wrk on windows 7.....

@rahulsahu it works very fine with windows 7, no problems whatsoever

@coderbanna, you mentioned you need to power it on for using it.
I tried it with power on/off, with battry and without battry....all four combinations
which does .

Any how if this needs battries to be inserted while using with simulator....i will go with http://rc4all.co.in/product_info.php?cPath=35_119&products_id=145

yes, using dedicated simulator remote is far better, cause you will definately need battery for that.

it's not work ...i said behalf of my personal experience..... 

Abhishek - did it work?

what did not work? comeone, tomorrow come online and give me teamviewer session , i will check and set it up.

@ rastsaurabh: no it did not work for me....i'm out of town for 2 weeks for office, see if you can do teamviewer session with coderbanna....if it works....i will also do it....

hello banna ji,
Appreciate your help but due to urgency will not be able to join till weekend. But in the meantime please help in providing the details as under.

> I am assuming FS 6ch tx can be used as remote.
> I have TX and cable which came with it ( bought it through RC Bharat)
> which S/w to be used to set the controls ( T6 which came with TX does not work on any of the com ports. I am yet to try Turborix and ATeasy.

> Which free simulator is available and from where it can be downloaded
> How to connect

regds.
Saurabh
>

Hello guys,
I just received my Tx-Rx (6Ch FlySky CT6B) yesterday from rcbazaar. I sat up for a long time trying to make it work with FMS and its done. I will post the proper instructions. I am running Windows 7 (32 bit).

I used this link for the info http://www.mycoolheli.com/CT6BHOWTO.html

Firstly, you need to have PPjoy and T6sim. Dont download the ppjoy in that webpage.
Make sure you have the latest PPjoy, the older one wont work !

Setup the Ppjoy virtual joystick by making a new virtual joystick and then mapping it with 6 axes, 2 buttons and 0 pov.
Open t6config and go to "open" and select the t6config file provided in the attachment from that webpage.
Select your com port and check if the bars are responding to joystick movement. CLOSE T6config ! Remember that!
Now open T6sim and open the port for your COM and then select the joystick.
Open FMS, calibrate your joystick and enjoy playing ! 

@jjaaxx44

I hope You will find the Solution in this thread .
http://www.rcindia.org/radios-and-receivers/configure-ppjoy-to-tx-for-free-simulation/

@bLoGgEr: Hi I did try your post and http://www.mycoolheli.com/CT6BHOWTO.html
I get problems when I get to step 10 and 11. I do not see com port even when I click open com.
I can see my device connected in T6config ans in device manager.

see attached images 1 and 2.

hi abhishek,
I could connect my tx on to vista. Do not try Simulators first connect the TX as is with t6 config. Remove all installations.
> do not connect anything to computer
> Have Usb drivers installed
> once USB drivers installed connect the cable to USB ( DO NOT CONNECT THE TX)
> See the device manager  ( try changing the port to 3,4) It can be done. There will be issue your Mouse dongle/ photon will be using these ports ... remove them.
> once you get the device on 3,4 port no. 
> Install T6 config & restart system
> check Device manager again
> connect the other end of cable to TX
> switch ON TX
> run T6, select the same port as in device manager
> check the sticks you should have synch
> Get user & save settings

With this steps i could connect TX to laptop. now searching for good simulator to practice.

Hope this helps  regds /// saurabh

realflight is top in my list, aerofly is very close.