I am sooo disappointed today. Since the last couple of days I seem to have been having a problem with the throttle trim tab on my Futaba 10C. The trim moves up properly, but when pulling it down, it works erratically.
My radio is less than a year old, and always been carefully used ( always in the box, and cleaned after every flight etc etc ) , I am soo pissed off.

My only solution here is to ship it to Futaba USA who are willing to service it for free ( since it is covered in warranty ) . I plan to ask them to ship it back to a US address, from where I can collect next month when I travel.
But thats going to leave me for over a month without radio !! and no flying !!!!

Just wanted to share that things like this can happen with top brands and products ! .
-Gaurav

Wonder is any kind of "cleaning of the contacts" is an option.  If under warranty, your current course of action is most sensible though.

Yes I had thought about cleaning the contacts. But read in the other forum about a post by someone that these switches are sealed and difficult to get to the real contacts.
The only drawback in sending it back to Futaba for replacement is that I will be left without flying for nearly a month. Guess I should revert back to building for sometime.

Just sent my Tx via TNT to Futaba Service Center USA, with a heavy heart.
Will collect it in May end when I travel. So one month with no flying !

Hi

This seems to be a problem with Futaba 10Cs....two of us in Bombay are victims for sure.

The other gentleman showed me the way. Open it up, dab petrol (nothing else) on the contact switch and keep pressing for a while. I did it just last week and it worked. And no seeming damage anywhere ! And I took a couple of flights later as well.

Now, I wouldn't recommend it because you ARE taking out the PCB which is right above the trim switches and the whole thing comes off etc etc...so at your own risk !

Cheers

GE

Awww dammm ... i seem to be a victim of this too .   . throttle and elevator trim  just work erratic  .

@Ge  After cleaning the contacts did it solve it permanently ? or id imagine  u  would have to keep cleaning it   ?

Its very frustrating to see this problem on one of the best radios. I eventually sent it to the Service Center, in the US  and they replaced the trim tab. Though it works fine now, i think the other trim tab might be on the way out as sometimes i need to juggle it to get it to work.

I have seen at least one instance of removing the battery and then applying one quick squirt of WD40 fix it.  The radio was not turned on for a few hours after this.

Did not go into the pros and cons of this, but it did work.

Short term solution: squirt of WD 40

Long term solution: replace the tactile switch. Easily available, at least in metros.

Since this is common, what is that one should ask for in the electronics parts shops ?  Any specific name or part number ?

I also saw similar issues with the slider pots on the bottom side of a 9C Super.

The switches are "ordinary" tactile switches. They come in a variety of sizes w.r.t the mounting pins spacing and height. You will have to remove the old one and take it as a sample. If someone can send me one I will organise enough for all and sundry!

Quote from: anwar on March 01, 2011, 04:12:27 PM
I also saw similar issues with the slider pots on the bottom side of a 9C Super.

Slider trims usually just rotate the control pots themselves, mechanically. Maybe they have separate pots in the 9C. In which case you would have to change the pots.

the reason why, i am holding onto to myskysport 35 mhz, it is dirty with oil stains, (Some permanent) been to all the dusty fields of raj, bihar east, all across india, and still works like a charm

I dont think i wud risk trying to send mine back to futaba , as re importing it would be difficult and my warranty is over . . It is a beautiful radio and its a shame that the trims act erratic .

@sushil . they still havent failed  completely so when they do . i might consider sending the switches to u

and Agustine i have a skysport too and i agree they last . but its unfortunate i cant fly a heli with it

It's not how clean you keep your radio it's about how much pressure you apply on trims when you are multitasking (flying and trimming at the same time.

Keep those thumbs light and keep your radio error free 

I am a victim of the same .... my new Futaba 8FG just 4 flights old stopped responding on the throttle trim today.... very disapointing I must say

Quote from: Hellyflyer on March 04, 2011, 07:53:44 PM
It's not how clean you keep your radio it's about how much pressure you apply on trims when you are multitasking (flying and trimming at the same time.

Keep those thumbs light and keep your radio error free 

Don't quite agree. The problem is oxidation of the switch contacts and increased pressure will, if at all, help rather than hinder.

O.k. its fixed.... opened it up cleaned it with petrol with the help of an ear bud..... ot of connections needed to be taken out and put back .... try at ur own risk .....

Quote from: divay99 on April 09, 2011, 07:03:10 PM
O.k. its fixed.... opened it up cleaned it with petrol with the help of an ear bud..... ot of connections needed to be taken out and put back .... try at ur own risk .....

What exactly do you clean? I am having the same problem. I did open my TX to see whether the buttond where working properly which they are but they seem not to be making correct contact with the plastic trigger. Can you please explain what do you clean? I am already without elevator and aileron trims Rudder is next

hi guys,
I bought a futaba 6ex 2 years ago,
18 months old and the transmitter board pack up. contacted futaba who said "throw it away and buy a new one"
futaba ...total rubbish for my thoughts
by cheap one or get dxi 100 % customer service with these people
regards
don

This happened with my Futaba 7C too! I wonder other OEM Tx owners are facing similar problem, else we really need to reach Futaba Quality department.

I simply replaces the micro switches under the Tabs. I could not get 'Hight quality' switches in the local market, else I would have replaced all the 8 switches under tabs. 

Yeah. Futaba has for sure made a mess on the quality of the trim tabs. Never had problems before and now everyone's complaining !

ujjwaana. Do you have a link of the switches you used to replace the worn out ones? I  think i broke my momentary trim buttons and need to replace them