Hello everyone,

I recently got supermicro rc gear from a fellow member. Today i was able to get it work with my radio, here is link to the schematic used. (2n2222, 6.8k, 20k all 1/4 watt, post 61)

http://www.rcgroups.com/forums/showthread.php?t=1147689&page=5

will keep you guys updated on the programing/setup once i have it installed on a model.

diy usb adapter for sanwa sd10g

http://www.aeroglide.net/2011/04/sauvegarde-sur-pc-de-votre-sd-10g/
http://blog.xuite.net/ep_fly/D2013/123087441-SANWA+%E8%B3%87%E6%96%99%E5%82%B3%E8%BC%B8%E7%B7%9A
http://blog.xuite.net/scumor/twblog/131736771-%E4%B8%8D%E7%94%A8+MegaPower+USB-Link+%E5%8D%87%E7%B4%9A+880DS++1.31+%E9%9F%8C%E9%AB%94
http://www.rcgroups.com/forums/showthread.php?t=1029192&page=185

Subscribed.

Finished radio and receiver test setup

Transmitter in mode 2, 80ohms coil, 4mm 32ohms motor, 1.27mm Berg connectors (M/F).

First set the transmitter/radio channel assignment.
Channel 1 = Throttle, Channel 2 = Aileron, Channel 3 = elevator, Channel 4 = Rudder
Next move/set the throttle trim to minimum, set the transmitter to PPM8 and connect the module.
Note: if the transmitter module receives a valid PPM signal then LED flashes and when no valid signal LED is solid.

Binding process for 3ch receiver (HK103RX-S).

1. Switch 1 = ON, all others = OFF (to use inbuilt ESC)
2. Power on the receiver. Wait 5 secs and Rx LED starts a repeating cycle of ON OFF ON LONG_OFF (described as "blink in jump way" in the manual). Rx is now awaiting binding.
3) Power on the Tx and press the binding switch. The module LED flashes GREEN once and you then release the binding switch. The module LED then starts flashing RED quickly.
4) Wait till the Rx LED changes from flashing to steady (about 3 secs).
5) Check to see controls work.

If it works, first power down the receiver then transmitter. You should only have to bind once. After that just turn on the transmitter (all 5 switch in off position) then receiver.

For members using other brand radios with Super-micro 2.4Ghz modules please read post 463 (link) to get switch settings info.

http://www.rcgroups.com/forums/showthread.php?t=1462072&page=31

Sahil

Servo connection to JR airplane receiver

1)THROTTLE, 2)AILERON, 3)ELEVATOR, 4)RUDDER

Next upgrade is the USB cable. FT232QR based UART 3.3V logic is the recommended in rcgroups forum and i will be ordering from element14.

http://in.element14.com/jsp/search/results.jsp?N=0&Ntk=gensearch&Ntt=FT232RQ&Ntx=mode+matchallpartial&suggestions=false&ref=globalsearch&_requestid=1955

Today afternoon i got a supermicro 5Ch brick with BL esc. After initial testing i find that servos have poor in resolution at slow speeds and sounds horrible   and 3.43 grams in weight 

Here are some pictures, uploading video.

Yesterday i picked 4No's of ADH50XL-3000 motor (7.4 grams) and i wanted to use then with HK super micro BL receiver. Searching on this motor spec. found a thread where the motor was setup for 1S and late night i was able to run the motor connected to receiver.

http://www.beatyourtruck.com/forum/showthread.php?78570-Mitchell-s-Brushless-Sukhoi-XP

I thought since i have similar KV 9 gram M1818/25 motor from RCB, why not test that as well to see if works and it does  .

will post a video later.

Sorry for the poor quality 

https://www.youtube.com/watch?v=gwTrCCHW6sg&feature=youtu.be

I was programing my radio and found my manual copy is not the latest.

Here is a link to latest Aero manual

http://www.airtronics.net/media/uploads/SD-10G_Aero_Setups_Guide.pdf

http://www.airtronics.net/media/uploads/751750_Airtronics_SD-10G_Operating_Manual_V2.pdf

First lot of FHSS-1 receivers from RCI member arrive  . Did quick bench testing of the receivers, need to do proper field testing 

The most important thing i noticed between RX841FS (1st airtronics 2.4Ghz receiver) and later receiver models is it has simple bind switch unlike the newer once where user has to poke the bind switch with something  , may be new design was to prevent accidental bind switch activation   

got first batch of Airtronics receivers from RCG, with these i can now finish of my pending micro builds 

interesting receiver conversion, RX500 5ch to 7ch receiver.

http://www.rcgroups.com/forums/showthread.php?t=1294618

How did i skip this thread