Quote from: Rooster on August 16, 2011, 01:47:52 PM
Once the RX is bound to the TX is there a process to debind the Rx from the TX. I need this because at any given point I want to use only one Rx.
I intend to use this radio  on my boat and rescue boat. Now assuming that my primary boat is stuck in middle of a lake and I need to send my rescue boat to get it back, and I have only this radio, I do not want the primary boat rx to respond to any functions when the rescue boat is operating since it will defeat the entire rescue operation .

Help Help!!!!!

Quote from: foamybuilder on August 16, 2011, 02:31:59 PM
Guys, anyone using turnigy after changing  frsky (the kit which directly solders)
Will the simulator work without any mods  after changing to frsky

Yes. I have been using the Turnigy 9X + FrSky DIY for a long time now. No probs with simulator. It works as good. No mods for sim required.

Hi,

http://rcbazaar.com/products/397-fs-th9x-9ch-24ghz-transmitter-receiver.aspx
I have seen FS -TH 9x tX in Rc bazaar site.can someone tell whether this tx is gud one to buy and what is the difference between turnigy and FS -9 channel.Actually i am looking for Turnigy tx, but i dont find it in indian stores.
Please give ur opinion on this FS -TH9x ?

thanks,
krian

Hello Kiran,

I m using Turnigy 9x which is similar to Flysky 9x, Copterx CX- CT9A, Imax 9x, they are all the same with just different brand names, rcbazaar has got the same Tx which is as good as Turnigy 9x.

There is a yahoo group dedicated to Flysky 9x, chk here : http://groups.yahoo.com/group/Flysky_RC_radio/


Regards,

Muzammil.

i bought the FS-th9x from rcbazaar, thanks for ur advice.

Quote from: Rooster on August 16, 2011, 01:47:52 PM
Once the RX is bound to the TX is there a process to debind the Rx from the TX. I need this because at any given point I want to use only one Rx.
I intend to use this radio  on my boat and rescue boat. Now assuming that my primary boat is stuck in middle of a lake and I need to send my rescue boat to get it back, and I have only this radio, I do not want the primary boat rx to respond to any functions when the rescue boat is operating since it will defeat the entire rescue operation .

Dear sreekanth,
i am using the Hobby king TX and RX but it is exactly the same as this one. The process of binding the second rx will unbind the first RX. So your purpose is solved

u r welcome kiran

Quote from: hangingtough on August 28, 2011, 06:45:15 AM
The process of binding the second rx will unbind the first RX. So your purpose is solved

@Hangintough... No this does not solve the problem. Even if the second RX is bound to the TX the first RX also accepts the signals. It does not get unbound ( not sure if this is correct word)

Shreekant

@kiranch19
Can you please tell the range that you are getting for TH-9X ?

Quote from: Rooster on August 29, 2011, 04:09:38 PM
@Hangintough... No this does not solve the problem. Even if the second RX is bound to the TX the first RX also accepts the signals. It does not get unbound ( not sure if this is correct word)

Dear rooster,
You are not correct, when you bind the second RX , the first RX will get auto disconnected.

Quote from: Rooster on August 16, 2011, 01:47:52 PM
Once the RX is bound to the TX is there a process to debind the Rx from the TX. I need this because at any given point I want to use only one Rx.
I intend to use this radio  on my boat and rescue boat. Now assuming that my primary boat is stuck in middle of a lake and I need to send my rescue boat to get it back, and I have only this radio, I do not want the primary boat rx to respond to any functions when the rescue boat is operating since it will defeat the entire rescue operation .

The Turnigy 9x has model memory so all you need to do is bind both the RX at differnt memory locations and then change the location on the TX .

Hellyflyer

Guys, I recently added rudders for f22 and am facing problem with prog mix.
Following is the setup.
Right servo is going to channel 6
Left servo is going to channel is 4

AUX-CH menu set to GEAR ( to enable it)
Prog.Mix Menu
Mix1
STATE          ACT
MASTER       RUD
SLAVE         FLP
OFFSET       000
UPRATE       100
DOWNRATE 100
SW             ON


Problem i am facing
Moving rudder stick to the right: Both rudders are moving to the right together (this is fine)
Moving rudder stick to the left: Left rudder moves completely to the left, right rudder is in neutral position.

Is there any configuration i need to add??