thank you,

and when i am moving the cyclic stick the servo movements are very slow?
is that normal ?

Yes cause the gyro is in sport mode so they will not move fast as ur learning Isuggest u ddon't change that in adjustment menu.. Ltr.. If u have read the manual ull know what I am talking about

okay,

i made gyro sense as
normal - 30
stunt 1-70

which one should i use when starting to config gyro?
in your video it was in blue
but i am getting purple status?

Set it to rate1 70 tht is heading hold mode pls of set the tail slider when rudder servo is central as seen in video to get proper setup

thank you for the support,

i will try setting up everything today

Hi,

we are configuring gyro in head locking mode and i am not gonna fly in rate mode,
do i need 30 in normal, whats the use?

thanks

the gyro inputs i gave u are just temporary  for now while flying u may have to increase or decrease the gain ...the % of gain depends on the servo type also mostly in heading hold mode u will need around 65% +-...rate mode is used to fly scale ...for people who like scale flying cause the helicopter behaves like a real one without the heading locking mode .....setup if done right works on both ...i hope u have offset ur tail pitch if its done right u will have to use little or no trims in heading hold and rate mode u just need to adjust gyro gain 

Thank you.

Sent from my MB525 using Tapatalk 2

i got the fbl head from RCBazaar,
how to fix it, washout base is moving freely on the main shaft,
do i need to tighten it, if then what height i need to fix it.

thanks

yes u have to tighten it first turn on your heli on then at mid stick check where the arms are level tighten there also check for any binding at full positive pitch if so just loosen and increase height slightly

also i recommend u change ur flybarless head later on when new stuff comes in rcbazaar all in one heads are better I,H or dfc is good too...

thank you,

when i give the rudder input the slider stays in one end(happens in both ends)and its not moving when i turn the heli, but it moves for the rudder input?(HH mode), and also without the rudder input gyro sensing and tail is working, but after rudder input its not sensing.

i checked for the binding but there is no binding because it works well in rate mode.

which colour does led display on gyro if its blue then heading hold mode if purple then rate and it behaves like that only lol no need to worry

okay, it blinks blue and its hh mode.

after rudder input, tail slides to end and when i turn the heli gyro is not sensing so slider not moving for any movement of the heli till there is a rudder input.

i am testing on the desk.

is this normal?

can u explain whats happening, sorry if i am wrong in anything

it blinks blue ?? it is supposed to be steady i hope u letting the gyro initiate completely

And also place the heli on a flat surface

sorry man,

it stays blue and if i change the gain below 50 it goes to purple.

hh and rate mode are fine.

in hh mode the gyro sense the heli movement and slider is moving when i turn the heli but after the rudder input the slider goes to one end and stays there, after that if i turn the heli the gyro is not sensing till i give stick input

heli is on flat surface and light is steady blue?

everything is fine till i give tx input after input the tail slides to one end and stays there till i give next input, its not sensing the heli movement

yup it is supposed to behave like that only dont worry just check your gyro is sensing in right direction that is the main thing

okay thank you, gyro is sensing right,

i was using avionic g560, but i couldnt remember how it was working.

the secondary set up where u adjust the gyro performance leave everything related to tail the way it is put heli on sport mode ,for u dont go higher it becomes very agile for a beginner .half stick movement will cause heli to roll lol  stay away from pro mode

sure thank you

in fb heli, i adjust the positive and negative swash level using endpoint adjust,
in fbl avionic x5 what should i do for leveling at full positive and negative?

thanks

u dont need too if it is level at mid stick ....this problem might occour if u using analog servos ...but for digital no problem...u cant use endpoints on this ....

i am using analog servos and swash is level at midstick but not at ful positive and full negative what should i do?