try trimming to arm your board,

and connect like this

1 BEC To KK Board + Rx

1 BEC Power to power 2 servos
1 BEC Power to power another 2 servos

Ok update.

Board is armed now.

Trimmed the values .

alls good.

FINALLLY !!

Coming back to the servo issue, that still is there.

..
..
..

1 BEC to Kk .. I dont get this , what is BEC ?

IN ESC DC power 5V Out coming from BEC.

ok .. so what do i do , connect which wire to where ?

also,, another query, in the T6 config (new one )

there is 'Switch A' ' Switch B'

How can i use them ? Assuming that they are for the knob on top of the Tx ?

I've put Mixers on CH5 and Ch6 for my servos

center wire(Usually Red) in servo to middle wire of BEC (Usually Red)

,, Wait ... I have to cut the wires ??

Switch A, Switch B are position switches that can be assigned to work as Ch5 or Ch6

sooraj: I didnt get it .. I assigned Thro Cut to Switch B

What does Dual rate do ?

ALSo, regarding the Self-Level of the KK , can i trigger it with the switch B ?

 Set  VR(A/B) to NULL
Enable MIX 2 as follows
Source VR(A/B)
Destination CH(5/6)
Up Rate 100
Down Rate 100
Switch A/B

Parichya, to solve this out, you might need to either rework the connectors on all your servos , or get a powerful separate BEC .

If you know soldering and is not ready to spend more, you can go with first option.

Quote from: parichya.gautam on January 07, 2015, 12:57:47 AM
,, Wait ... I have to cut the wires ??

No just unplug that from the connector,

Akhil: I had done that but put the values at -100 and set it on reverse XD, changed it now.
didnt get the "Set  VR(A/B) to NULL" part.
ALSO, is it possible that instead of turning the mixer for the servo, i use the switch and it does the same work as the mixer ( IE, move the servo)  ?

ALSo, what is the use of DUAL RATE

@Sooraj:

no , no more spending or soldering is there a way i can do it without any cutting or buying XD ?

OH !! please explain again , what to unplug and where to put in ?

and BTW , I was able to put both on a single switch

used Switch A for servo retracts

look at the picture, that single connector is from breadboard jumper,

Quote from: parichya.gautam on January 07, 2015, 01:13:22 AM
and BTW , I was able to put both on a single switch

used Switch A for servo retracts

yes you can but you need to connect all signal wires together to channel 5/6

You can use ch5 in your Tx to self level on/off - so assign this to two position switch A (don't know how it is done in this radio - akhilzid could help)
And Ch6 for your retracts - assign Ch6 to switch B .

Can I know how many y connectors are you using and are you connecting all this servos to a single receiver channel ?

Akhil: I dont have that Cable

sooraj: i have 3 connectors , to make a final 4-1 connection

After assigning ch6 to switch B, you have to connect all your servo signal leads to Ch6. But power to your servo needs to be splitted.

yes i know that , that is want to know how do I do that without splitting any wires or buying anything new

did you cut any cables from BEC while connecting KK board?

For doing it with out any more expenses you have to do some cutting / soldering .
For doing it with out hassle of cutting cables or soldering, get 2 more servo splitters.

Quote from: parichya.gautam on January 07, 2015, 01:23:20 AM
yes i know that , that is want to know how do I do that without splitting any wires or buying anything new

if you powering KK board from 1 ESC and you have linear regulator, then you can connect that cable back, that will give more amps will help a lot in this case.

Akhil - No nothing

sooraj : 2 more ?? for what I could get it ...

Akhil M1 esc powers the board ..