DIY home made V-tail mixer

TRISHUL 1994 · February 11, 2016, 11:22:00 PM

the programming can't be done.... i am using pic16f84a with conventional jdm programmer and win pic but it is showing error while verifying the hex file... i am using the same set up as described in "philip sun" site...
plzzzz give me some suggestion .....

sahilkit · February 14, 2016, 10:23:05 PM

can you post more info and in the meantime check your fuse settings

16F84A : OSC= XT, WDT= ENABLE, PWRT= ENABLE , CP= BLANK(DISABLE)

TRISHUL 1994 · February 15, 2016, 12:53:01 AM

yeah i am trying it from first time.... but no luck.... the "winpic" is showing the error in the code..

sahilkit · February 15, 2016, 10:09:43 PM

trishul can you conform if the ic is working with different code like a led blinker hex? by any chance you enabled code protect at the time of burning the code ?. Let me dig up the one i built and get back.

Can you post a screen shot of error message. Post some pictures of your setup.

Sahil

sahilkit · February 15, 2016, 10:18:53 PM

the jdm2 programmer i built has option to select b/w pic16 or 24XX, yours selected correctly?

TRISHUL 1994 · February 15, 2016, 10:25:42 PM

yeah i tried it again...no luck....

.... i will post the screen shots tomorrow....

sahilkit · February 15, 2016, 10:37:17 PM

this is what i have used and try ic-prog

http://197.14.51.10:81/pmb/ELECTRONIQUE/mise%20a%20jour/Microcontroller/How%20to%20build%20your%20own%20PIC-Programmer.pdf

sahilkit · February 15, 2016, 10:37:53 PM

http://www.ic-prog.com/

Edit: so the programmer is working fine ? and the ic too ? but just not with this code ?

TRISHUL 1994 · February 16, 2016, 10:04:09 AM

i think so... because in the time of verification of ic the programmer is is working fine and it also recognising the pic.... but during programming the first two lines of hex file is becoming red...

GAGAN DEEP · February 22, 2016, 09:09:03 PM

hey do you still build the V tail mixers?
If yes then i would like to buy 5..
if no then please can you give me the circuit diagrams?
Thanks

sahilkit · February 22, 2016, 09:19:02 PM

see post 1 (all the info is there)

Sahil

sahilkit · February 22, 2016, 09:20:05 PM

http://ilufa.orgfree.com/MIXER_E.htm

YashasR · March 15, 2017, 09:08:14 AM

can i use this PIC12F508

YashasR · March 15, 2017, 09:36:57 AM

and can I use "USB 2.0 to UART TTL 5PIN Connector Module Serial Converter CP2102" for programming? If yes then how?
link : http://www.amazon.in/REES52-Module-Serial-Converter-Replace/dp/B01I6MXWV2?tag=googinhydr18418-21&tag=googinkenshoo-21&ascsubtag=6a9b81b0-bb88-4d55-8b48-4b024f4ba2b2

YashasR · March 15, 2017, 10:31:12 AM

Hello, I have made the etching design for this V-tail Mixer, Would be happy to share with you all.

Please correct me if I am wrong.

sahilkit · March 15, 2017, 03:03:45 PM

Quote from: YashasR on March 15, 2017, 09:36:57 AM
and can I use "USB 2.0 to UART TTL 5PIN Connector Module Serial Converter CP2102" for programming? If yes then how?
link : http://www.amazon.in/REES52-Module-Serial-Converter-Replace/dp/B01I6MXWV2?tag=googinhydr18418-21&tag=googinkenshoo-21&ascsubtag=6a9b81b0-bb88-4d55-8b48-4b024f4ba2b2

IF you already have rs232 pic programmer and need/use USB then it will work otherwise NO.

sahilkit · March 15, 2017, 03:05:37 PM

Quote from: YashasR on March 15, 2017, 09:08:14 AM
can i use this PIC12F508

Should work but check your fuse settings and don't burn code with one time write.