http://www.hobbyking.com/.../__43056__130mm_Corn_Light...

http://www.hobbyking.com/.../__26408__LED_Corn_Light_12V...

http://www.hobbyking.com/.../__43733__115mm_Male_JST_SH_1...

http://www.hobbyking.com/.../__40044__Turnigy_TX...

ALL OF THESE will go together right ? No connection issues here .. ??


Need to be perfectly sure ...

Connection i have in mind:

Rx--->Relay--->Corn LED Splitter--->CornLED Adaptor--->Corn LED

Help me here guys ...

Rx--->Relay--->CornLED Adaptor--->Corn LED
is fine.

cant find any use with this
http://www.hobbyking.com/.../__43733__115mm_Male_JST_SH_1...
between this.

also you need to give power to relay input.

.. power to the relay input ...won't it take power from the board ?

im not getting the complete picture here... a little explanation ?

http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=38002&aff=53708

If i buy this

http://www.hobbyking.com/hobbyking/store/__43056__130mm_Corn_Light_Adapter_With_JST_Female_Connector.html


ALSO, for these , I have the Y-Splitter cables for servos, If i use them , it should work right

power to relay(for switching) will take from rx,
but you need to provide power for led through the other lead(you can see two leads other than rx connector, one of them is power in from batttery/bec and other is power out to led)

i think i got it ..

mentioning what i am going to do.

Buying things:

http://www.hobbyking.com/hobbyking/store/__38002__Dr_Mad_Thrust_series_3A_BEC_with_Inbuilt_Aux_Controlled_On_Off_Switch_for_Accessories.html

http://www.hobbyking.com/hobbyking/store/__43056__130mm_Corn_Light_Adapter_With_JST_Female_Connector.html

http://www.hobbyking.com/hobbyking/store/__26408__LED_Corn_Light_12V_1_5W_10_LED_White_2pcs_.html

http://www.hobbyking.com/hobbyking/store/__26424__LED_Corn_Light_12V_2_6W_13_LED_Red_2pcs_.html

Servo Y-Splitter cables.


I will connect the BEC the way it is seen in the video.

Will use Y-Cable to connect the JST adaptors which are in-turn  connected to the LEDs.

Correct ?

No issues here right ?

Quote from: parichya.gautam on February 24, 2015, 01:19:45 AM
http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=38002&aff=53708

If i buy this

this one only outputs 5/6V and selected  led is 12V this combination will not work

so better is previous combination with http://www.hobbyking.com/.../__40044__Turnigy_TX...

OH !!! ...

so i have to choose LED which dont use more than 6v

or is there something similar which can power the 12v LEDS ??

I just need something that I can control from my Tx ...

for 12v power, if you are goind to use with 3s battery then take power direct from battery.

yes i will be using a dedicated LiPo for the LEDs ( same battery that i will be using for my FPV system )

with that it will work ??

yes that should work.

oh !! ..

let me confirm it once again ..

if I connect it to my 3s LiPo , then the LEds will work ? they will get 11.1v ??

yes you are correct,

to be clear about connection check attached image.

... you mean this ?

I thought you were talking about the Dr Mad Thrust one ??


Please confirm, DMT or the turnigy one ?

Once again, will connect to my 3 LiPo

that depends on led power.

For 5/6v(up to 2amps) LED use DMT

turnigy relay controlled one can power any thing under 60W but you need to provide proper power to input of the relay(that act like a normal switch between input and output).

ok .. so if powered by the lipo , there shouldnt be any issues right ??

yes, right.

ok cool : D


thanks , ordering now

one quck question .... JST female will fit in the Servo male lead naa ??

simply no. they shouldn't work.

then I have 4 JST Female connectors ( http://www.hobbyking.com/hobbyking/store/__43056__130mm_Corn_Light_Adapter_With_JST_Female_Connector.html )

to be connected to the LED part of the Relay ... how do you do that ?? Can you point out to some harness if any from HobbyKing ??

http://www.hobbyking.com/hobbyking/store/__23347__JST_XH_to_JST_LED_Power_Distribution_Lead_6_JST_.html

THIS CAN WORK ?? !! .. no ?