Hi,
We did not get this version for India. We have the 30 acc and 1/55 acc. version currently in India range

Which is best Dremel 4000 or 3000?

Which is best accessory to cut alluminium ? SC456 or SC541 or 561 ? I purchased Dremel 4000 1/45 from Delhi.

Hi all, can i use this dremel clone model (110V) without any modification.... or will it fry itself if i connect it to our standard 230v supply......................

Are there any better clones in indian market , which i can buy online.................

http://www.rcbharat.com/getproductdetails.php?id=14

pls somebody show some response.......

It will FRY

thank u divay sir

Use 220 to 110 V converter available in local market.

How many hobbyists out there use Dremel in Bangalore? We are looking at hosting an event for Dremel users to interact, share hobby ideas, interesting tips etc!

Do reply!

I just bought a Dremel 300. What did you have in mind?

I bought a Dremel 300 with 55pc Accessory Set, Flexi Shaft and moulded case for Rs.4600 all inclusive. 6 months Warranty.

Thanks a lot to VC for putting this up. I called Hari and he's extremely helpful! The store was very crouded and he patiently answered ALL my questions and opened up several products so that I can have a peep. Another person, whose name evades me, was also keen on helping me out. Explained a lot of stuff and spoke about several products. Excellent customer service.

HIGHLY RECOMMENDED!

Quote from: VC on January 18, 2010, 10:22:37 PM
Sri Varu Power Tools company
22, SJP Road,
Bangalore - 560002.
Mr. Hari - 098450 50209 - extremely polite and helpful.

Ordered a multichuck and drill bit set on ebay. Looking forward to getting those!

What dremel to get to cut out stripped hex screws? It will be used only for that purpose. Please suggest one.

Quote from: mail4ajo on May 02, 2013, 09:06:03 PM
What dremel to get to cut out stripped hex screws? It will be used only for that purpose. Please suggest one.

I usually use the cut-off wheel (540/456) for the screw head to make a slot and use a screw driver to remove it.

If that fails, cut out the head and carefully drill (628) it out. Though the first method works 99% percent of the time.

If you're talking about the Dremel itself, any model will get the job done. If this will be its exclusive use, I suggest getting a cheap clone and using dremel bits. Any 3.2mm chuck will accept all dremel accessories.

Hope this helps!

Tassem.

I have no clue on dremels. Please suggest a model, wheels, accessories to get. I prefer a cheap one as its for very rare use. I hardly strip my screws as I use high quality wrenches and am patient with my cars.

buy the dremel 100 or chinese die grinder if u want dremel for stripped screws, for some extra hobby work dremel 300 will suffice.

Wouldn't a normal screw extractor work?

Just got Dremel 4000 4/65 from Machpowertools....and a multi vice, clamps, and a workbench....hope to be able to take care of lots of small jobs...will keep on building the accessory inventory...

Where is a good place to buy one? I don't mind a clone. Only use us lean body sanding and cutting screws.

Hi Vidhar, how did the event go?

Quote from: vidhar on January 09, 2013, 05:24:40 PM
How many hobbyists out there use Dremel in Bangalore? We are looking at hosting an event for Dremel users to interact, share hobby ideas, interesting tips etc!

Do reply!

Hi Vidhar,
how did the event go? Please share your experience.
Thanks

My new set of Dremel 4000 4/65 with skil work bench....all have been sourced from Machpowertool....

 

I just made a small order of 4k with machpowertools for the first time, let us see how it goes

I am sure you will have a good experience. I mean I did.. they are prompt and reasonable...only sometimes their payment gateway does not work...

Congratulations mrfixit4u. Good to note they reorganized the flexishaft holder in the case. In the 300 series, the flexishaft keeps falling off.